All,
Thanks for the lot of good hints and sorry for late response, but som of you
got lC6st in my Spam folder...
I will try it next weekend band keep you updated.
RegardsB
Sven Koch #2224
GesendetB vonB meinemB BlackBerryB 10-Smartphone.
B Originalnachricht B
Von: diraxel@hush.com
Gesendet: Dienstag, 17. Mai 2016 14:54
An: sk-svenkoch@gmx.de
Cc: bricklin@autox.team.net
Betreff: Re: [Bricklin] How to fasten the front wheel bearing
Sven,
I had to replace my front wheel bearings last year, and unfortunately, the
passenger side failed after 600 km. I think the wheel nut was probably
tightened a bit too much: the nuts were backed off about a 1/4 turn (according
to AMC documentation). I inquired about that on the mailing list right here,
and according to the feedback I got (thank you again guys ;), it is supposed
to be tightened until the hub binds while turning, then backed off about a
half turn, rather than a 1/4 turn. Granted, it may depends too on how tight
the nut is originally tightened...
Eventually, when I replaced the bearings again, the nuts were tightened until
they binded (turn your disc/rotor from times to times to eliminate the slack),
but then with a half turn, the nut really felt loose, so it was rather backed
off about a third turn. I put more than a thousand kilometers on the odometer,
drove the car in the tight curves of a mountainous area and both sides have
been fine.
On Tuesday, May 17, 2016 at 2:17 AM, "Christopher Blizzard"
<blizzard@0xdeadbeef.com> wrote:
>
>The Bricklin manual has something different. It says to install
>the bearings,
>tighten to 20-25 ft-lbs while turning the hub to seat the
>bearings. Then back
>off about 1/3 of a turn and tighten the bolt to 2-10 inch lbs.
>(inch!). So
>that works too.
>
>Sent from a portable phone device thing
>
>> On May 16, 2016, at 10:46 AM, John T. Blair <jblair1948@cox.net>
>wrote:
>>
>> At 05:46 PM 5/15/2016, sven koch wrote:
>>
>>> the 4 screws of the mounting plate for the front wheel. Getting
>everything
>>> together was not a big challenge, but now my question is how to
>> tight/ adjust the
>>> wheel bearing.
>>
>> Sven,
>>
>> Quoting from the Chilton's AMC manual,
>>
>> "Place the hub assembly onto the spindle and install the inner
>> lockring and outer bearing. Install the wheel bearing nut and
>torque
>> it to 50 Ft Lb, while turning the wheel back and forth to seat
>the
>> bearings. Back off the nut about 1/4 turn (90deg) max."
>>
>> John
>>
>>
>> John T. Blair WA4OHZ email: jblair1948@cox.net
>> Va. Beach, Va Phone: (757) 495-8229
>>
>> 48 TR1800 48 #4 Midget 65 Morgan 4/4 Series V
>(B1106)
>> 75 Bricklin SV1 (#0887) 77 Spitfire 71 Saab Sonett III
>> 65 Rambler Classic
>>
>> Morgan: www.team.net/www/morgan
>> Bricklin: www.bricklin.org
>>
>> If you can read this - Thank a teacher!
>> If you are reading it in English - Thank a Vet!!
>>
>> From Dennis Prager - The American Trilogy:
>> e pluribus Unum, "from many, one."
>> In God We Trust
>> Liberty - the power of choosing, thinking, and acting
> for
>> oneself; freedom from control or
>restriction
>>
>>
>>
>>
>> ---
>> This email has been checked for viruses by Avast antivirus
>software.
>> https://www.avast.com/antivirus
>> _______________________________________________
>> Bricklin@autox.team.net
>> Donate: http://www.team.net/donate.html
>> Suggested annual donation $11.47
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage:
>http://autox.team.net/mailman/options/bricklin/blizzard@0xdeadbeef.
>com
>_______________________________________________
>Bricklin@autox.team.net
>Donate: http://www.team.net/donate.html
>Suggested annual donation $11.47
>Archive: http://www.team.net/archive
>Forums: http://www.team.net/forums
>Unsubscribe/Manage:
>http://autox.team.net/mailman/options/bricklin/diraxel@hush.com
_______________________________________________
Bricklin@autox.team.net
Archive: http://www.team.net/archive
|