I tried to follow this design but I connected the rod with the spring mount
which gives an angle.
The angle has the advantage of an anti dive but it seems to stiffen up the
suspension and acting like a sway bar.
Too unpredictable.
https://lh3.googleusercontent.com/-KSmOrPC6I2s/T8plfWxpLFI/AAAAAAAABXs/VDma4
UruAsA/s761/CCI02062012_0000.jpg
Cheers
Chris
-----Urspr|ngliche Nachricht-----
Von: J.C. Hassall [mailto:jhassall@blacksburg.net]
Gesendet: Samstag, 2. Juni 2012 20:48
An: MadMarx
Cc: fot@autox.team.net
Betreff: Re: [Fot] LSD
On 6/2/2012 2:04 PM, MadMarx wrote:
> I used an idea from a engineering book but I suppose that the angle of the
> rod is too large.
> I drove into a McDonald parking when the left rod snapped.
> With one working rod the on-off-throttle steer was back again...greatly
more
> than it was but the car felt much better.
> So I'm going back to the stock situation and remove the rods.
>
> Cheers
> Chris
> And thank you all for input. Learned a lot.
>
>
>
Chris, as I recall from my old DP car with a Detroit Locker
differential; the car would squat to one side or the other under
acceleration/deceleration; after I installed a set of torque rods the
problem went away. It is important to have the axis of the rod parallel
to the frame when the car is at half suspension travel. That should
minimize surprises as the suspension hits the limits, as Duncan said
below. By the way, it appeared from your video that the rods were
welded to the top of the axle. Mine were mounted to a plate under the
spring pad; the front of the rods mounted to a bracket I welded to the
frame.
I have some pictures of a Traction Master rod like I had installed which
I can send if you want them.
Gluck auf!
jim
> -----Urspr|ngliche Nachricht-----
> Von: Duncan Charlton [mailto:duncan.charlton54@gmail.com]
> Gesendet: Samstag, 2. Juni 2012 19:38
> An: MadMarx
> Betreff: Re: [Fot] LSD
>
> Chris,
>
> Does the rod's arc of movement exactly match that of the axle? That is,
> does the front mount of the reaction rod use the same axis of rotation as
> the front eye of the spring? If not, it's trying to twist the axle
relative
> to what the spring is doing, creating resistance to movement, adding roll
> stiffness.
>
> Another approach might be to clamp together the front leaves of the spring
> but leave the rears alone. One other solution I've seen (on a Sunbeam
> Tiger) was to wrap the front end of the second leaf around the spring eye
> bushing (inside the main leaf eye, and using a smaller-diameter bushing),
> effectively doubling the stiffness of the front half of the spring.
>
> Duncan
> (Texas)
>
> On Jun 2, 2012, at 12:08 PM, MadMarx wrote:
>
>
>> Hi Guys,
>>
>> I installed rods to the axle.
>>
>> http://youtu.be/QPCCN96x8_U
>>
>>
>> The leaf spring is now calmated but the car does oversteer badly.
>> Seems to stiffen up the suspension now.
>> I'm not sure if I should maintain that idea.
>>
>> Cheers
>> Chris
>
--
Jim Hassall
Blacksburg VA
'63 TR4 in autox preparation
99% finished, 90% to go
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/fot/mharc@autox.team.net
|