tigers
[Top] [All Lists]

Re: [Tigers] Lower Grill Trim

To: tigers@autox.team.net
Subject: Re: [Tigers] Lower Grill Trim
From: Gary <maliburevue@yahoo.com>
Date: Sun, 22 Jan 2012 17:23:59 -0800 (PST)
I just used some screws and ground the heads enough to fit into the groove of
the trim piece so they wouldn't turn and then slid them in the end of the
trim.
 
Gary

--- On Sun, 1/22/12, Joe Brown <jbbrown1980@gmail.com> wrote:


From: Joe Brown <jbbrown1980@gmail.com>
Subject: Re: [Tigers] Lower Grill Trim
To: "'Gary Winblad'" <garywinblad@comcast.net>, rfraser@bluefrog.com
Cc: tigers@autox.team.net
Date: Sunday, January 22, 2012, 4:34 PM


Yes, there is a slight curve to the trim piece.  I got lucky and was able to
feel where the original holes where from underneath and then I used a small
drill bit to come up through them.  I knew I was in the right place because
I didn't hit anything but paint and bondo.  For fasteners I guess I will
find some nylon screws that fit.



Thanks,

Joe



  _____ 

From: Gary Winblad [mailto:garywinblad@comcast.net]
Sent: Sunday, January 22, 2012 4:19 PM
To: rfraser@bluefrog.com
Cc: 'Joe Brown'; tigers@autox.team.net
Subject: Re: [Tigers] Lower Grill Trim



My trim piece is not straight, it has a slight curve tapering back
from the center..

Gary

----- Original Message -----
From: Ron Fraser <rfraser@bluefrog.com>
To: 'Joe Brown' <jbbrown1980@gmail.com>, tigers@autox.team.net
Sent: Sun, 22 Jan 2012 19:03:48 -0000 (UTC)
Subject: Re: [Tigers] Lower Grill Trim

Joe
    I believe if you run a straight line across the opening at the body
sheet metal, set the finisher inboard on that line; the fastener holes will
be at the center line of the finisher.

There are only 4 fasteners.   Difficult to get at the Front of my Tiger
right now but the center 2 seem to be about 4" from the center of the grille
and the outer ones seem to be about 4" from the ends.

The part numbers for that finisher and the side mouldings fasteners are
different but that does not mean they will not work.  I used a butterfly
style clip with a nut to hold mine down.   I have the number for that clip
somewhere; I just need to look for it.

Ron Fraser

-----Original Message-----
From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
On Behalf Of Joe Brown
Sent: Sunday, January 22, 2012 1:08 PM
To: tigers@autox.team.net
Subject: [Tigers] Lower Grill Trim


Hi,



Can anybody send me a good photo showing exactly where the lower grill
"finisher" trim sits on the front valence?  When body work was done on my
car the holes were filled in and I can't find where they were.  From digging
through the archives I found that this piece of trim uses the same fasteners
as the side trim.  But I'm not sure how many fasteners there were.



Thanks,

Joe Brown

Arlington, TX

B382000217
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/tigers/rfraser@bluefrog.com




-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2012.0.1901 / Virus Database: 2109/4755 - Release Date: 01/20/12
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/tigers/garywinblad@comcast.net
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/tigers/maliburevue@yahoo.com
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums


<Prev in Thread] Current Thread [Next in Thread>