triumphs
[Top] [All Lists]

[Fot] GT6'rs

Subject: [Fot] GT6'rs
From: bschirano at yahoo.com (Brian Schirano)
Date: Sun, 21 Jan 2018 19:25:15 +0000 (UTC)
References: <1224117856.2342511.1516542950594.ref@mail.yahoo.com> <1224117856.2342511.1516542950594@mail.yahoo.com> <E9834EF9-C7D8-4FC5-A2A5-45F73E95D9A0@me.com> <C187B47F-6B7C-4CF6-9B87-4815325CFF74@yahoo.com>
Thanks everyone so far, my thoughts and tentative plans:   
   - weld another bung on the valve cover for venting, was a suspect problem
   - leak down, good idea, motor build isn't that old, but never know
   - bell housing clearance, that's a SOB when I R&R the engine to begin with. 
if I do a lift I will remove the throttle linkage, that will give me at last a 
little room. I think I have a cable linkage in a box of spares that I have been 
wanting to install.
   - pan dimpling, that pan just went on a year ago and I angle ground dressed 
it, so should have been pretty good.
   - sealing block, agreed, next time that motor is out it get's a steel one.?
Thanks guysBrian


26A GT6+, 28 TR6Brian Schirano
585-305-0349 Cell?
BSchirano at yahoo.com 

    On Sunday, January 21, 2018, 6:50:02 PM GMT+1, Larry Young <cartravel at 
yahoo.com> wrote:  
 
 I have found that leaks are often caused by a PO-gorilla has over tightened 
and made a dimple at the holes. You can see this clearly with a belt sander. I 
hammer the dimples down until the belt sander contacts everywhere. This applies 
to front covers and pans.?- Larry

Sent by big thumbs on tiny screen.?
On Jan 21, 2018, at 10:23 AM, Scott Janzen via Fot <fot at autox.team.net> 
wrote:



I?ve never done it. ?Certainly not without lifting the engine somewhat, and by 
the time you undo the water hoses, engine mounts, etc, you are halfway to 
pulling it. ?If you try, you might want to look at how much of a gap there is 
between the top of the bellhousing and the firewall, as this could inhibit the 
lift.
Venting - I ended up with a 1? and a 1/2? hose on the valve cover and this 
cured most of the blow-by issues at the rear seal, etc. ?The 1/2? hose was not 
enough, so now there are two. ?Also tried a vent off the fuel pump mounting 
before the valve cover vents, but the pump cam slung so much oil in this 
direction that it didn?t work.
If you are getting oil leaks at the front, that fun sealing block may be the 
issue.


On Jan 21, 2018, at 8:55 AM, Brian Schirano via Fot <fot at autox.team.net> 
wrote:
OK GT6 guys...
Question... is it possible to pull the pan and change my gasket without pulling 
the engine? Looks pretty tight and I expect the oil pump pick up snorkel will 
be the problem.Is a partial lift possible to do this?
It looks?like it's pushing oil out of the pan, it's definitely not the timing 
chain cover (that's what I thought last year and changed that).?

2nd question, if it's pushing oil out the front of the pan (or anywhere from 
pan I suppose), I'm thinking I need more crankcase vent? and maybe get around 
this problem short term that way?
Let me know, making garage work plans/list of things to do, for when winter 
breaks early March
ThanksBrian
26A GT6+, 28 TR6Brian Schirano
585-305-0349 Cell?
BSchirano at yahoo.com_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/archive




_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/archive



  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180121/5dbc1a6a/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>