fot
[Top] [All Lists]

Re: [Fot] Dreaded Thrust Washers in the Oil Pan

To: "Lorne Fritz" <lfritz82@hotmail.com>, <gaf3@charter.net>,
Subject: Re: [Fot] Dreaded Thrust Washers in the Oil Pan
From: "Geoff Byrne" <gkbyrne@optushome.com.au>
Date: Fri, 7 May 2010 18:38:05 +1000
I have always run a full circle thrust washer on clutch side . I mill the 
bearing cap. I can send specs if required
Geoff Byrne
TR6 racer down under
----- Original Message ----- 
From: "Lorne Fritz" <lfritz82@hotmail.com>
To: <gaf3@charter.net>; <fot@autox.team.net>; <6pack@autox.team.net>
Sent: Friday, May 07, 2010 1:36 PM
Subject: Re: [Fot] Dreaded Thrust Washers in the Oil Pan


> This is more common than you think.  Iv'e had to repair  several.
> If your lucky the larger size washers will take care of the end play, but 
> the
> real problem is it usually wears off the tabs on the bottom main bearing 
> cap
> which holds the washers in place.  To fix this you can add weld to the cap 
> and
> carefully grind it back to the original shape and or pin the washers with
> brass to the block. Of coarse the crank would need to come out to put the 
> pins
> in.     Good luck,  Lorne
>> Date: Thu, 6 May 2010 17:13:45 -0400
>> From: gaf3@charter.net
>> To: fot@autox.team.net; 6pack@autox.team.net
>> Subject: [Fot] Dreaded Thrust Washers in the Oil Pan
>>
>> Group
>> I've been working on a friends 74 TR6 and we discovered lots of crank
>> end play.
>> I checked the end play because he was complaining of hard shifts or
>> grinding while putting the trans in reverse.
>> I removed the pan and found the thrust washers in the oil pan..
>> I've run into large end play issues with the TR6's but this is the first
>> I've seen in the pan.
>>
>> Understanding that this is a common malady with the TR6, I ordered a few
>> sets of oversize thrust washers.
>> Don't think there is enough material in a .025" oversize bearing to fix
>> the problem.
>>
>> I pulled the bearing cap and didn't see major wear in the thrust face of
>> the crank. I will need to do a closer inspection of the block
>>
>> Anyone out there seen a reasonable/simple fix for this problem?
>>
>> Thanks in advance
>> Glenn Franco
>> TR6's, 250 and Spit racer
>> _______________________________________________
>> fot@autox.team.net
>>
>> http://www.fot-racing.com
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe: 
>> http://autox.team.net/mailman/options/fot/lfritz82@hotmail.com
>>
>>
>
> _________________________________________________________________
> The New Busy is not the too busy. Combine all your e-mail accounts with
> Hotmail.
> http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID2832
> 6::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: 
> http://autox.team.net/mailman/options/fot/gkbyrne@optushome.com.au
_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums


<Prev in Thread] Current Thread [Next in Thread>