fot
[Top] [All Lists]

[Fot] TR6 transmission rebuild - counter shaft gears

Subject: [Fot] TR6 transmission rebuild - counter shaft gears
From: fubog1 at aol.com (fubog1)
Date: Tue, 9 Jan 2018 06:40:30 -0500
 What Steve said, this is the way to do it.
Also I recently noticed that Moss is selling a double bearing gear now.
Glen
 

 

-----Original Message-----
From: Steve Yott <tr4 at wi.rr.com>
To: van.mulders.marcel <van.mulders.marcel at telenet.be>; 'fubog1' <fubog1 at 
aol.com>
Sent: Mon, Jan 8, 2018 7:01 pm
Subject: RE: [Fot] TR6 transmission rebuild - counter shaft gears



For all gearboxes I rebuild and for a number of other builders I modify the lay 
gear by boring the 1st gear end in order to fit a double bearing which pretty 
much eliminates bearing and shaft failure.  There is too much load on the 
bearing and shaft in this area and the double bearing installation mimics the 
more durable Stag gearbox.  At the same time I machine a groove in the end to 
fit a circlip to prevent bearing walk.  I also use Loctite retaining compound 
to add a little further fixing for the bearings.
 
Steve Yott
Silver Lake Triumph Centre
 

From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of 
van.mulders.marcel--- via Fot
Sent: Monday, January 08, 2018 12:20 PM
To: fubog1 <fubog1 at aol.com>
Cc: fot <fot at autox.team.net>
Subject: Re: [Fot] TR6 transmission rebuild - counter shaft gears

 

These shell needle bearings are easily damaged : when the shell is warped a 
bit, it will fail. When the bearing is in place, one should check if the 
needles can be spinned freely.

A nylaton bush of the TR4a -TR6 inner wishbone bearing is great for pushing 
these shell bearings in place. These bearings are not secured by a circlip, 
contrary to the open cage needle bearings.

But the needles of the open cage bearings are running directly against the ev. 
worn or damaged inner surface of the laygear.

Marcel

 



Van: "fot" <fot at autox.team.net>
Aan: gblake58tr3 at icloud.com, "fot" <fot at autox.team.net>
Verzonden: Maandag 8 januari 2018 15:33:33
Onderwerp: Re: [Fot] TR6 transmission rebuild - counter shaft gears

 

It probably has the later type shell bearings and 1 or both have worked loose 
in the laygear housing bore and "milled" into the thrust washer (s).
Glen



 

 

 

-----Original Message-----
From: Greg Blake via Fot <fot at autox.team.net>
To: Fot <fot at autox.team.net>
Sent: Sun, Jan 7, 2018 8:56 pm
Subject: [Fot] TR6 transmission rebuild - counter shaft gears

I am rebuilding a TR6 transmission and ran into a strange snag. When I removed 
the countershaft the counter shaft gears did not drop to the bottom of the 
case. I had to tap on the counter shaft gear set with a brass punch to get them 
to move far enough to allow the input shaft and gear to be removed. Now that I 
have the main shaft out of the case, I can't get the counter shaft gears out of 
the case. I've been able to move them a little bit by tapping on the gears with 
a brass punch through the drain hole but I can't get them out. Has anyone run 
into this before? Any ideas to get them out?

Thanks. 

Greg

Sent from my iPhone
_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/archive




_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/archive



-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180109/dafe019b/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>