healeys
[Top] [All Lists]

Re: [Healeys] Bn2 excessive oil pressure

To: "'Alan Seigrist'" <healey.nut@gmail.com>, "'Jose Vicente Vargas'"
Subject: Re: [Healeys] Bn2 excessive oil pressure
From: "Herbert Miller" <hgmiller3@qwest.net>
Date: Sun, 22 May 2011 10:42:20 -0500
Please tell me why an air bubble in the gauge line would cause the gauge to
read incorrectly.

Herb Miller 

-----Original Message-----
From: healeys-bounces@autox.team.net [mailto:healeys-bounces@autox.team.net]
On Behalf Of Alan Seigrist
Sent: Sunday, May 22, 2011 10:02 AM
To: Jose Vicente Vargas; Bob Spidell; Healey List
Subject: Re: [Healeys] Bn2 excessive oil pressure

Sometimes if there's an air bubble in the guage line, it will read
incorrectly.  Disconnect from back of guage, run motor for a few seconds
until squirting out, then re-attach....

Alan

On 5/22/11, Jose Vicente Vargas <jvvmusme@yahoo.com> wrote:
> I have dennis welch oil pump
> Using 20-50w oil
> The holes of the adapter are correctly aligned  This situation afyer 
> the oil and filter change
>
>
>
> Sent from my iPad
>
>
> On May 22, 2011, at 8:39 AM, Bob Spidell <bspidell@comcast.net> wrote:
>
>> Jose,
>>
>> Regardless of the filter, the oil pressure relief valve should limit 
>> the
> pressure to a maximum of (typically) 60-70psi.
>>
>> 30psi @ 1,000rpm is great, but 90 @ 4,000 seems too high; the obvious
> culprit would be the valve, but I can't explain how just changing the 
> oil and filter would instigate the problem (unless, maybe, you went 
> from 20W break-in oil to straight 60W).  Definitely check the valve 
> for burrs, etc.; maybe try a different spring.
>>
>> Sounds like your rebuild was good--most issues are with too low
> pressure--but too high puts undue stress on the cam/distributor gear 
> and seals.
>>
>> Bob
>>
>> --------------------------------
>> Bob Spidell - San Jose, CA
>>
>>
>>
>> After the engine rebuilt I had normal oil pressure 20-30 at 1000 rpm 
>> and
> 40-50
>> At 4000 rpm.
>> Using the spin oil filter adapter from moss and the cheap fram spin 
>> on oil filter (moss # 235-880) After an oil and filter change this 
>> week I get 30 at 1000 rpm and 90 at
> 4000
>> rpm and 100 at 5000 rpm. I changed the oil spin on filter to the K&N 
>> (moss
> #
>> 235-830).
>> Any ideas,
>>
>> Jose
> _______________________________________________
> Healeys@autox.team.net
> Donate: http://www.team.net/donate.html Suggested annual donation  
> $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/healey.nut@gmail.com
>

--
Sent from my mobile device
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/healeys/hgmiller3@qwest.net
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

<Prev in Thread] Current Thread [Next in Thread>