--===============3171391338015253584==
boundary="----=_Part_372935_1952773514.1438220674745"
------=_Part_372935_1952773514.1438220674745
Content-Transfer-Encoding: 7bit
I think there is too much corrosion to warrant trying to use the bores as is. I
don't think that a servo is so precious that I should save it by sleeving, so
it is available for parts.Ken Freese65 BJ8
----- Original Message -----
From: goldengt@cal.net
To: goldengt@cal.net
Cc: healeylist <healeys@autox.team.net>
Sent: Tue, 28 Jul 2015 08:35:53 -0700 (PDT)
Subject: brake servo dismantling complete
body {height: 100%; color:#000000; font-size:12pt; font-family:arial,
helvetica, sans-serif;}I drilled and tapped a 10-32 hole in the plug, made a
little puller and got the plug out. I did not have a flat bottom tap, but .200
deep on the hole drill point gave enough threads.Ken Freese
----- Original Message -----
From: goldengt@cal.net
To: healeylist <healeys@autox.team.net>
Sent: Tue, 21 Jul 2015 17:26:12 -0700 (PDT)
Subject: [Healeys] brake servo dismantling
I have been saving an old BJ8 servo to rebuild for many years. I have gotten
the main bore seals out and it looks ok, but I cannot not get the control valve
piston plug out of the body to get access to the control valve seals. The
instructions say use some stiff wire to push it out, but it isn't budging.
Should I just assume this is an indicator of sufficient corrosion to scrap the
whole unit?Ken Freese65 BJ8
------=_Part_372935_1952773514.1438220674745
Content-Transfer-Encoding: quoted-printable
<html><head><style> body {height: 100%; color:#000000; font-size:12pt; font=
-family:arial, helvetica, sans-serif;}</style></head><body><div>I think the=
re is too much corrosion to warrant trying to use the bores as is. I don't =
think that a servo is so precious that I should save it by sleeving, so it =
is available for parts.</div><div>Ken Freese</div><div>65 BJ8</div><div><br=
></div><div>----- Original Message -----<br>From: goldengt@cal.net<br>To: g=
oldengt@cal.net<br>Cc: healeylist <healeys@autox.team.net><br>Sent: T=
ue, 28 Jul 2015 08:35:53 -0700 (PDT)<br>Subject: brake servo dismantling co=
mplete<br></div><div><br></div><style> body {height: 100%; color:#000000; f=
ont-size:12pt; font-family:arial, helvetica, sans-serif;}</style><div>I dri=
lled and tapped a 10-32 hole in the plug, made a little puller and got the =
plug out. I did not have a flat bottom tap, but .200 deep on the hole drill=
point gave enough threads.</div><div>Ken Freese</div><div><br></div><div>-=
---- Original Message -----<br>From: goldengt@cal.net<br>To: healeylist <=
;healeys@autox.team.net><br>Sent: Tue, 21 Jul 2015 17:26:12 -0700 (PDT)<=
br>Subject: [Healeys] brake servo dismantling<br></div><div><br></div><div>=
I have been saving an old BJ8 servo to rebuild for many years. I have gotte=
n the main bore seals out and it looks ok, but I cannot not get the control=
valve piston plug out of the body to get access to the control valve seals=
. The instructions say use some stiff wire to push it out, but it isn't bud=
ging. Should I just assume this is an indicator of sufficient corrosion to =
scrap the whole unit?</div><div>Ken Freese</div><div>65 BJ8</div><div><br><=
/div><div><br></div></body></html>
------=_Part_372935_1952773514.1438220674745--
--===============3171391338015253584==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============3171391338015253584==--
|