This is a multi-part message in MIME format.
--===============5738410070694093167==
boundary="----=_NextPart_000_002D_01D194C7.9A07F2F0"
Content-Language: en-us
This is a multi-part message in MIME format.
------=_NextPart_000_002D_01D194C7.9A07F2F0
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
=20
=20
Well, I=E2=80=99ve always done this.
1) Put a piece of masking tape over the drilling point. Then =
another over that. Push them down tight so they=E2=80=99re making close =
fit.
2) Mark the start position through the tapes with a bradawl.
3) Start drilling with a hand drill and a small, sharp(!!) drill =
bit. Sharp bit. Slow, steady pressure. Nice and straight so no skidding.
4) Drill a nice little pilot hole. You should be OK by hand and, =
I=E2=80=99m guessing, that the metal isn=E2=80=99t too thick if =
it=E2=80=99s painted.
5) Go up a size drill bit and drill with an electric drill, nice =
and steady does it. Keep it slow and straight so it won=E2=80=99t want =
to jump out.
6) Keep going up in size until you get the right size hole.
Don=E2=80=99t forget what may be lurking on the other side of the =
painted surface...it may not like being drilled!
Simon
------=_NextPart_000_002D_01D194C7.9A07F2F0
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" =
xmlns:o=3D"urn:schemas-microsoft-com:office:office" =
xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml"; =
xmlns=3D"http://www.w3.org/TR/REC-html40";><head><meta =
http-equiv=3DContent-Type content=3D"text/html; charset=3Dutf-8"><meta =
name=3DGenerator content=3D"Microsoft Word 12 (filtered =
medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
@font-face
{font-family:Tahoma;
panose-1:2 11 6 4 3 5 4 4 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0cm;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman","serif";}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
p.MsoAcetate, li.MsoAcetate, div.MsoAcetate
{mso-style-priority:99;
mso-style-link:"Balloon Text Char";
margin:0cm;
margin-bottom:.0001pt;
font-size:8.0pt;
font-family:"Tahoma","sans-serif";}
p.MsoListParagraph, li.MsoListParagraph, div.MsoListParagraph
{mso-style-priority:34;
margin-top:0cm;
margin-right:0cm;
margin-bottom:0cm;
margin-left:36.0pt;
margin-bottom:.0001pt;
font-size:12.0pt;
font-family:"Times New Roman","serif";}
span.EmailStyle18
{mso-style-type:personal;
font-family:"Calibri","sans-serif";
color:#1F497D;}
span.BalloonTextChar
{mso-style-name:"Balloon Text Char";
mso-style-priority:99;
mso-style-link:"Balloon Text";
font-family:"Tahoma","sans-serif";}
span.EmailStyle21
{mso-style-type:personal-reply;
font-family:"Calibri","sans-serif";
color:#1F497D;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;}
@page WordSection1
{size:612.0pt 792.0pt;
margin:72.0pt 72.0pt 72.0pt 72.0pt;}
div.WordSection1
{page:WordSection1;}
/* List Definitions */
@list l0
{mso-list-id:1647008133;
mso-list-type:hybrid;
mso-list-template-ids:-2075260650 134807569 134807577 134807579 =
134807567 134807577 134807579 134807567 134807577 134807579;}
@list l0:level1
{mso-level-text:"%1\)";
mso-level-tab-stop:none;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level2
{mso-level-tab-stop:72.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level3
{mso-level-tab-stop:108.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level4
{mso-level-tab-stop:144.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level5
{mso-level-tab-stop:180.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level6
{mso-level-tab-stop:216.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level7
{mso-level-tab-stop:252.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level8
{mso-level-tab-stop:288.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
@list l0:level9
{mso-level-tab-stop:324.0pt;
mso-level-number-position:left;
text-indent:-18.0pt;}
ol
{margin-bottom:0cm;}
ul
{margin-bottom:0cm;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DEN-GB link=3Dblue =
vlink=3Dpurple><div class=3DWordSection1><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><o:p> </o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><o:p> </o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Well, I=E2=80=99ve always done this.<o:p></o:p></span></p><p =
class=3DMsoListParagraph style=3D'text-indent:-18.0pt;mso-list:l0 level1 =
lfo2'><![if !supportLists]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><span style=3D'mso-list:Ignore'>1)<span style=3D'font:7.0pt "Times =
New Roman"'> =
</span></span></span><![endif]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Put a piece of masking tape over the drilling point. Then another =
over that. Push them down tight so they=E2=80=99re making close =
fit.<o:p></o:p></span></p><p class=3DMsoListParagraph =
style=3D'text-indent:-18.0pt;mso-list:l0 level1 lfo2'><![if =
!supportLists]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><span style=3D'mso-list:Ignore'>2)<span style=3D'font:7.0pt "Times =
New Roman"'> =
</span></span></span><![endif]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Mark the start position through the tapes with a =
bradawl.<o:p></o:p></span></p><p class=3DMsoListParagraph =
style=3D'text-indent:-18.0pt;mso-list:l0 level1 lfo2'><![if =
!supportLists]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><span style=3D'mso-list:Ignore'>3)<span style=3D'font:7.0pt "Times =
New Roman"'> =
</span></span></span><![endif]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Start drilling with a hand drill and a small, sharp(!!) drill bit. =
Sharp bit. Slow, steady pressure. Nice and straight so no =
skidding.<o:p></o:p></span></p><p class=3DMsoListParagraph =
style=3D'text-indent:-18.0pt;mso-list:l0 level1 lfo2'><![if =
!supportLists]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><span style=3D'mso-list:Ignore'>4)<span style=3D'font:7.0pt "Times =
New Roman"'> =
</span></span></span><![endif]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Drill a nice little pilot hole. You should be OK by hand and, =
I=E2=80=99m guessing, that the metal isn=E2=80=99t too thick if =
it=E2=80=99s painted.<o:p></o:p></span></p><p class=3DMsoListParagraph =
style=3D'text-indent:-18.0pt;mso-list:l0 level1 lfo2'><![if =
!supportLists]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><span style=3D'mso-list:Ignore'>5)<span style=3D'font:7.0pt "Times =
New Roman"'> =
</span></span></span><![endif]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Go up a size drill bit and drill with an electric drill, nice and =
steady does it. Keep it slow and straight so it won=E2=80=99t want to =
jump out.<o:p></o:p></span></p><p class=3DMsoListParagraph =
style=3D'text-indent:-18.0pt;mso-list:l0 level1 lfo2'><![if =
!supportLists]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'><span style=3D'mso-list:Ignore'>6)<span style=3D'font:7.0pt "Times =
New Roman"'> =
</span></span></span><![endif]><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Keep going up in size until you get the right size =
hole.<o:p></o:p></span></p><p class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Don=E2=80=99t forget what may be lurking on the other side of the =
painted surface...it may not like being drilled!<o:p></o:p></span></p><p =
class=3DMsoNormal><span =
style=3D'font-size:11.0pt;font-family:"Calibri","sans-serif";color:#1F497=
D'>Simon<o:p></o:p></span></p></div></body></html>
------=_NextPart_000_002D_01D194C7.9A07F2F0--
--===============5738410070694093167==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============5738410070694093167==--
|