--===============2537881503646841077==
--001a1144641e6cb44f0542ecede8
This morning I drained my old engine oil on my 100 and replaced the oil
filter, then refilled the sump to the correct level and restarted the
engine to check for oil pressure.
After several seconds I became concerned when the oil pressure gauge needle
stayed pegged. I also have a low oil pressure warning light, the sender
for which is mounted to the block at the point where the flex hose normally
attaches and it is staying lit.
By this time I had run the engine for at least 30 seconds and was becoming
very concered, so I shut it down, removed the valve cover and disconnected
the banjo bolt going to the rocker shaft, then restarted the engine--no oil
is coming out of the bolt.
Thinking that perhaps the oil pump lost prime I removed the flex hose from
the coiled copper pipe gong to the oil pressure gauge and back-fed some
engine oil, then reattached the hose to the line but on restarting again
nothing has changed.
Though this has never happened before I have heard of oil pumps not
repriming themselves and/or taking a while to do so after an oil change. I
have already run the engine for at least a minute in the several restarts
and am frankly concerned that serious damage may have already happened.
Any thoughts or suggestions will be appreciated.
Best--Michael Oritt
--001a1144641e6cb44f0542ecede8
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr"><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)=
">This morning I drained my old engine oil on my 100 and replaced the oil f=
ilter, then refilled the sump to the correct level and restarted the engine=
to check for oil pressure.</div><div class=3D"gmail_default" style=3D"colo=
r:rgb(51,51,255)"><br></div><div class=3D"gmail_default" style=3D"color:rgb=
(51,51,255)">After several seconds I became concerned when the oil pressure=
gauge needle stayed pegged.=C2=A0 I also have a low oil pressure warning l=
ight, the sender for which is mounted to the block at the point where the f=
lex hose normally attaches and it is staying lit. =C2=A0</div><div class=3D=
"gmail_default" style=3D"color:rgb(51,51,255)"><br></div><div class=3D"gmai=
l_default" style=3D"color:rgb(51,51,255)">By this time I had run the engine=
for at least 30 seconds and was becoming very concered, so I shut it down,=
removed the valve cover and disconnected the banjo bolt going to the rocke=
r shaft, then restarted the engine--no oil is coming out of the bolt.</div>=
<div class=3D"gmail_default" style=3D"color:rgb(51,51,255)"><br></div><div =
class=3D"gmail_default" style=3D"color:rgb(51,51,255)">Thinking that perhap=
s the oil pump lost prime I removed the flex hose from the coiled copper pi=
pe gong to the oil pressure gauge and back-fed some engine oil, then reatta=
ched the hose to the line but on restarting again nothing has changed.</div=
><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)"><br></div><div=
class=3D"gmail_default" style=3D"color:rgb(51,51,255)">Though this has nev=
er happened before I have heard of oil pumps not repriming themselves and/o=
r taking a while to do so after an oil change.=C2=A0 I have already run the=
engine for at least a minute in the several restarts and am frankly concer=
ned that serious damage may have already happened.</div><div class=3D"gmail=
_default" style=3D"color:rgb(51,51,255)"><br></div><div class=3D"gmail_defa=
ult" style=3D"color:rgb(51,51,255)">Any thoughts or suggestions will be app=
reciated.</div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">=
<br></div><div class=3D"gmail_default" style=3D"color:rgb(51,51,255)">Best-=
-Michael Oritt</div></div>
--001a1144641e6cb44f0542ecede8--
--===============2537881503646841077==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============2537881503646841077==--
|