This list could go on and on and on, and most all on them are reversable if
you want to go back to original.
Tube shocks front and rear
Torrington Bearings in front upper trunnions
Heavy duty sway bars front and rear
Torque bars on rear end
Headers
New steering column worm to eliminate slop
Retractable seat belts
Inertia fuel pump cut off
Cruise control
Power brakes on the earlier cars
Aluminium Radiator with or without pusher fan
LED strip underdash lighting
Power supply outlets
David Nock
British Car Specialists
209-948-8767
www.britishcarspecialists.com
-----Original Message-----
From: Bruce Steele
Sent: Friday, March 03, 2017 6:59 AM
To: pdzwig at summaventures.com ; 'Healey'
Subject: Re: [Healeys] Engine Rebuild Modifications
Good point. Everyone that I know who has Putzke's Fahrpass tube shock
conversion loves it.
Bruce Steele
Brea, CA
1960 BN7
-----Original Message-----
From: Healeys [mailto:healeys-bounces at autox.team.net] On Behalf Of Peter
Dzwig
Sent: Friday, March 03, 2017 12:57 AM
To: Healey <Healeys at autox.team.net>
Subject: Re: [Healeys] Engine Rebuild Modifications
It all depends what YOU want out of the exercise.
Interesting that no-one has mentioned handling and ride comfort.
I would do the usual mods to the engine, with the DW cam or similar (I used
a version of the race version of the BJ8 cam which went really well because
it was tailored to my requirements). High compression pistons work well with
a modern-fuel-compatible head and modern set up. Personally I used Hepolites
Lighten as much as poss and make sure it is all balanced and that whatever
your heating/cooling needs are, are taken care of and make sure that you
avoid excessive heat to the fuel lines. Carbs can be whatever you want.
Personally I like SUs but not everyone does.
I mention ride because when you have done all that you do to your engine and
transmission, it has to be usable when you drive it. I drove a couple of
Healeys recently both of which had more power than they could reasonably
handle over the sort of roads we were on. Look at your suspension carefully
and make sure that you get the level of firmness that YOU want. I used poly
bushes, anti-roll bars and tinkered with bits to get a ride that was good
enough to impress the late Alan Cameron storming up Prescott (which he ran
at the time).
Peter
>> On March 2, 2017 at 6:07 AM 1 2 <healeydohdahman at gmail.com> wrote:
>>
>> Hi All,
>>
>> Is there a list of commonly done rebuild mods for the 3000
>> engine/transmission to modernize it?
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html Suggested annual
>> donation $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>>
>> Healeys at autox.team.net
>> http://autox.team.net/mailman/listinfo/healeys
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/healeys/bspidell at comcast.net
>>
--
===========================================================
Dr Peter Dzwig
_______________________________________________
$12.75
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
http://autox.team.net/mailman/options/healeys/healeybruce at roadrunner.com
_______________________________________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
http://autox.team.net/mailman/options/healeys/healeydoc at sbcglobal.net
|