I have the same problem with checking, nice to see there is a solution.
Just to be 100% sure, which carbon wire should I buy, what car does it come
from?
Niels
Fra: Healeys [mailto:healeys-bounces at autox.team.net] P? vegne af David Nock
British Car Specialists
Sendt: 23. april 2017 16:39
Til: Bob Haskell
Cc: Healey List
Emne: Re: [Healeys] distributor cap
The carbon wire will not last if you leave it there
. However if you I stall one temporarily to set the timing and the replace it
with the copper wire.
David Nock
British Car Specialists
Stockton Ca 95205
209-948-8767
www.britishcarspecialists.com <http://www.britishcarspecialists.com/>
Please feel free to view an interview with the Nock's in 2009
Enjoy
www.youtube.com/watch?v=QOTTRYkbQzs
.
.
Sent from my iPad
On Apr 22, 2017, at 5:55 AM, Bob Haskell <rchaskell at earthlink.net> wrote:
Joesf,
I wasn't planning to change to carbon ignition wires for driving, just for
checking the timing.
Cheers,
Bob Haskell
AHCA 3000 MkI registrar
http://www.ciahc.org/registry_3000mk1.php
On 04/22/2017 03:55 AM, josef-eckert at t-online.de wrote:
Installing carbon ignition wires in your classic sports car, Austin-Healey,
Jaguar, MG, Triumph, etc. are the worst you can do anyway. They are prone to
fail after some period of time and cause intermittent interruptions. The engine
bay and the area where the wires run close to the engine, exhaust, etc. are
much too hot.
Josef Eckert
Konigswinter/Germany
-----Original-Nachricht-----
Betreff: Re: [Healeys] distributor cap
Datum: 2017-04-22T02:10:46+0200
Von: "Bob Haskell" <rchaskell at earthlink.net>
An: "David Nock BCS" <healeydoc at sbcglobal.net>, "Healey List" <healeys at
autox.team.net>
David,
The instruction manual suggested the same. I wasn't sure how well the
carbon wire would work with the screw style cap. Thanks.
Cheers,
Bob Haskell
AHCA 3000 MkI registrar
http://www.ciahc.org/registry_3000mk1.php
On 04/21/2017 01:06 PM, David Nock BCS wrote:
Bob, Make a carbon wire to install when setting the timing on the #1
plug wire. The replace it with the copper core wire to drive the car.
This on the only way I have found to check the timing here in the shop
David Nock
British Car Specialists
209-948-8767
www.britishcarspecialists.com
-----Original Message----- From: Bob Haskell
Sent: Friday, April 21, 2017 7:12 AM
To: Healey List
Subject: [Healeys] distributor cap
Listers,
I bought a used Snap On timing light and the instructions state that it
doesn't work with solid copper core spark plug wires. It doesn't. As
the carbon wires don't work well with the screw terminals in the
distributor cap, I was wondering if there was a cap for the DM6A
distributor for push on plug wires.
Cheers,
Bob Haskell
AHCA 3000 MkI registrar
http://www.ciahc.org/registry_3000mk1.php
_______________________________________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
http://autox.team.net/mailman/options/healeys/healeydoc at sbcglobal.net
_______________________________________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
?
_______________________________________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20170424/9159578d/attachment.html>
|