oletrucks
[Top] [All Lists]

RE: [oletrucks] What Next Ah Ha

To: "'oletrucks@autox.team.net'" <oletrucks@autox.team.net>
Subject: RE: [oletrucks] What Next Ah Ha
From: "Peters, Jon C" <jpeters@sikorsky.com>
Date: Tue, 7 May 2002 16:14:32 -0400
I've got a starter sitting on the floor of my shop that must be a conversion
year. Its the right one for the foot peddle unit but has a bolt on electric
solenoid, I got it with a 57 235 I put in my 51 coupe. 

Jon 

                -----Original Message-----
                From:   Bob KNOTTS [mailto:raknotts@qwest.net]
                Sent:   Tuesday, May 07, 2002 3:08 PM
                To:     Ray Archambeault; oletrucks@autox.team.net
                Subject:        Re: [oletrucks] What Next  Ah Ha

                I didn't know that. Bob K in PHX,AZ
                ----- Original Message ----- 
                From: "Ray Archambeault" <archambeault@earthlink.net>
                To: <oletrucks@autox.team.net>
                Sent: Tuesday, May 07, 2002 11:45 AM
                Subject: [oletrucks] What Next Ah Ha


                > My name is Ray and that alone might tell it all.
                > I asked the group why my starter just spun and did not
engage.
                > A kind soul advised me that the Bendix might be bad.
                > This morning I woke up expecting to remove and then
purchase a new
                > starter.
                > 
                > I had wanted to be able to see the fan blade turn since I
had just
                > installed a short
                > shaft water pump and different fan blade. Not much
clearance !
                > After carefully removing the coil wire and while standing
outside the
                > truck along side the starter, I pressed down on the pad
under the lever.
                > 
                > It just spun and did not engage.
                > 
                > I settled in for the tedious task of removing the starter,
disconnected
                > the battery
                > which I had charged all night thinking it needed more
juice, and got my
                > tools set up.
                > I had to clean up the garage first as thinking and
cleaning dont go
                > together.  I had made a big mess trying different methods
of finding my
                > problem and things were scattered all over.
                > I had started at seven AM and here it was ten.
                > I finally removed the starter and found that the bendix
was fine, though
                > it was very loose.  I had thought that it was jammed when
I last
                > installed the starter.
                > Why did the bendix move so freely.  Should't there be a
spring ? What
                > makes it engage ?
                > It is now 11;30
                > I finally had someone get in the truck and press the
started pedal and
                > it cranked OK.
                > Most of you now know what my problem was and when you stop
laughing I
                > will confirm what you have been thinking.
                > As I said before my name is Ray.  Only Mom called me
Raymond and that
                > was 50 years ago.
                > Have you stopped laughing.
                > 
                > THE FLOOR STARTER LEVER AT THE TOP OF THE STARTER
                > PIVOTS AND MOVES THE GEAR FORWARD AND MECHANICALLY ENGAGES
THE STARTER.
                > You knew that right.!!!!!!!    Ah Ha !
                > "Where do these people come from"   I said it first !!
                > oletrucks is devoted to Chevy and GM trucks built between
1941 and 1959
                oletrucks is devoted to Chevy and GM trucks built between
1941 and 1959
oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959

<Prev in Thread] Current Thread [Next in Thread>