oletrucks
[Top] [All Lists]

RE: [oletrucks] 53 1-ton panel ideas and questions

To: "'Jay Baker'" <jaybaker@ruralnetwork.net>,
Subject: RE: [oletrucks] 53 1-ton panel ideas and questions
From: "Thomas, Robert" <RThomas@ButteCounty.net>
Date: Wed, 20 Nov 2002 11:14:03 -0800
Gents:  Last I looked a Dodge or Ford diesel & trans was in the $5,500-8,500
range, depending on mileage (hours).  You can probably talk to an insurance
company & get the whole truck for that $$.

My $0.02.

RT


-----Original Message-----
From: Jay Baker [mailto:jaybaker@ruralnetwork.net] 
Sent: Wednesday, November 20, 2002 6:12 AM
To: Brad Kahler; oletrucks@autox.team.net
Subject: Re: [oletrucks] 53 1-ton panel ideas and questions

I have similar plans for my one ton panel this is kinda  ideas ive been
toyin with . i also plan on towing

1. 235 with 56 od 3 speed column shift setup with a over  under   brownie
with stock rearend (fentons)

2. Cummins Diesel with auto od setup for towing

 with setup 1 it would be a 1:98 final drive for flat long stretches and
also be able to shift under for pulling hills i have everything but the
brownie and i know were one is if i can talk the guy out of it.

The second setup would work good to but have ya priced a new cummins or used
for that matter lately.

 also may do the conventional small block 700 r4 but I like to be different
lol
----- Original Message -----
From: "Brad Kahler" <brad.kahler@141.com>
To: <oletrucks@autox.team.net>
Sent: Tuesday, November 19, 2002 1:43 PM
Subject: [oletrucks] 53 1-ton panel ideas and questions


> My wife and I are trying to decide how  to configure and
> rework our newly purchased 53 1-ton panel.
>
> We plan to be able to use it for towing a 24' enclosed race
> trailer over moderate (200 miles) to long (2000) mile trips.
>
> What we currently have in mind is the following,
>
> 1) Change to a small block V8 reworked with towing in mind
>
> 2) Leave the ride hight as it currently is, which is stock with
> 16" wheels (which I don't believe are stock).  We like the
> looks as it sits now.
>
> 3) Not sure which automatic transmission to use but possibly
> one with overdrive.  I don't know much about chevy
> transmissions so this will need some research.
>
> 4) Change to power brakes located down on the frame rail.
>
> 5) Either change the rear axle to a more modern unit from a
> 1-ton or change the ring and pinion to something more
> suitable for todays highway speeds, again keeping in mind
> that we'll be towing a trailer.  Are there different ratios
> available for the 53 1-ton rear end?
>
> 6) Change the suspension to a 3/4 ton chevy truck front
> suspension allowing us have power steering while keeping
> the 8 lug wheels and still get the larger truck disk brakes.
> Also this should provide a somewhat better ride.  I've found
> someone locally that does these conversions for a living and
> does very nice work.
>
> 7) Not sure what to do about the stock rear brakes.  Possibly
> there is some conversion out there to a better drum brake
> setup, or better yet are the stock rear brakes good brakes?
>
> 8) Not sure what to do about the steering wheel/column.  We
> would kind of like to keep the stock look in that area but will
> look at all possibilities here.
>
> 9) Add A/C using one of the uder dash kits being sold today.
> Will lilkely have to add an evaporator in the rear as well,
> considering how long this panel is.
>
> 10) Dual frame mounted gas tanks to increase the capacity
> to around 35 gallons or so.
>
> Hope all this makes sense....!
>
> Brad
> 1953 1-ton panel (texas)
> oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959

<Prev in Thread] Current Thread [Next in Thread>