spridgets
[Top] [All Lists]

[Spridgets] revisit to yapered wheel bearings

Subject: [Spridgets] revisit to yapered wheel bearings
From: soavero at yahoo.com (Ron Soave)
Date: Sun, 13 Feb 2011 06:52:31 -0800 (PST)
Same here, knock wood. I DID have issues because of the way the races of
certain bearings' inner diameters not having a compatible radius with the
wheel hub. If you follow the MGB procedure, you can get shims from McMaster
Carr. Just call Peter C. and he'll hook you up with everything you need.
While you're at it, I highly recommend Mini Mania's billet hubs. There are not
cheap, but not absurd either.

Ron



--- On Sun, 2/13/11, fastvee
<fastvee at yahoo.com> wrote:

> From: fastvee <fastvee at yahoo.com>
> Subject: Re:
[Spridgets] revisit to yapered wheel bearings
> To: spridgets at autox.team.net,
"Leo" <60bugeye at cebridge.net>
> Date: Sunday, February 13, 2011, 6:00 AM
>
Leo,
> I installed taper rollers in my SCCA race car many years
> ago because
I felt
> they would hold up better with the large wheel offsets and
> 8" wide
slicks, and
> the frequent disassembly. I followed recommended practice
> of
using shims and
> the original distance spacer so the nut could be torqued
>
like the ball
> bearings are. Essentially you would use the MGB front
>
bearing adjustment
> procedure. The car has been through several owners since
> then and is back in
> my hands, and the bearings and spindles still look
good. I
> still use ball
> bearings in my 74 Midget because there isn't a
compelling
> reason to change,
> and they work well enough. Here is an
excellent article
> which covers the
> details.
>
http://www.mgexperience.net/article/mg-midget-wheel-bearings.html
> John
>
Fogelsville, PA
> 
> --- On Sun, 2/13/11, Leo <60bugeye at cebridge.net>
> wrote:
> 
> From: Leo <60bugeye at cebridge.net>
> Subject: [Spridgets] revisit to
yapered wheel bearings
> To: spridgets at autox.team.net
> Date: Sunday, February
13, 2011, 4:34 AM
> 
> I know this subject has been visited before BUT  what
>
is the REAL world
> consensus on the long term reliability of the tapered
wheel
> bearing
> conversion such as http://tinyurl.com/63d2bnu   . 
>  
Anybody that has done
> the conversion and had success with it (high mileage
>
success)?  Any
> failures?  I have seen and experienced a spun bearing
> /
ruined hub and want
> to avoid the issue again but I also question the wisdom
of
> changing a
> "heavily factory engineered"  component (engineering
> which
far exceeds the
> capabilities of the typical car owner).  A
> catastrophic
failure at speed
> (low or high) of the front end is not a failure I want to
>
experience. 
> 
> 
> 
> Thanks
> 
> Leo
> Suggested annual donation  $12.75
>
Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
Unsubscribe/Manage:
>
http://autox.team.net/mailman/options/spridgets/fastvee at yahoo.com
> 
> 
> 
>
>  
> ________________________________________________________________________
> ____________
> Looking for earth-friendly autos? 
> Browse Top Cars by
"Green
> Rating" at Yahoo! Autos' Green Center.
>
http://autos.yahoo.com/green_center/
>
_______________________________________________
> 
> Donate:
http://www.team.net/donate.html
> Suggested annual donation  $12.75
> Archive:
http://www.team.net/archive
> Forums: http://www.team.net/forums
>
Unsubscribe/Manage:
http://autox.team.net/mailman/options/spridgets/soavero at yahoo.com

<Prev in Thread] Current Thread [Next in Thread>