triumphs
[Top] [All Lists]

Re: Tie Rod Ball Joint Puller Group Purchase

To: 6-Pack <6pack@Autox.Team.Net>,
Subject: Re: Tie Rod Ball Joint Puller Group Purchase
From: Don Malling <dmallin@attglobal.net>
Date: Sun, 06 Feb 2005 23:59:13 -0500
Based on Dave's post below, I will continue with the purchase.

The list is at 37. I'll order 40. I'll see if they'll give me a price break.

Lots of list members use the two hammer method to separate the ball joints and 
tie rods. I guess 
this tool could be viewed as an aid to that method.

In addition to David, another list member has used it and also recommends it.

I guess if it's junk, we can't say that Thomas didn't warn us.

If anyone wants out, let me know soon. I will call and order tomorrow (Monday).


Don Malling

  1. Dennis Lambert   blambert@socal.rr.com
  2. Oliver           sumton@sbcglobal.net
  3. Bob Labuz        yellowtr@adelphia.net
  4. Bill Schooler    schooler@adelphia.net
  5. Mike             mjanacek@snet.net
  6. Adam Baesley     abeasley@samgroup.com
  7. Steven Humphrey  behappy@insightbb.com
  8. Tony Cascio      whosgoofy@adelphia.net
  9. Charles Chesire  cachuck2000@sbcglobal.net
10. Aaron Cropley    Acekraut11@aol.com
11. Jim Holmgren     jholmgren@advertising.com
12. Maynard Hirsch   mghirsch@netzero.net
13. Jim Davis        jdavis344@bellsouth.net
14. Adrian Tedder    teddera@coolaccess.net
15. Mark Hooper      mhooper@digiscreen.ca
16. Larry Daniels    ladaniels@sbcglobal.net
17. Glenn Rattmann   k6na@cts.com
18. Jay Snable       jsnable@mac.com
19. David Council    dcouncill@msubillings.edu
20. Robert McBride   rmcbride@twmi.rr.com
21. Steve Shoyer     Steve@shoyer.com
22. Harold Sawatsky  hsawatsk@sasktel.net
23. Don Malling      dmallin@attglobal.net
24. Rick Brown       mgrick@mgcars.org.uk
25. James            Lbcnut@aol.com
26. George Re        mgman71@verzion.net
27. Charles Dubois   duboistr3@yahoo.com
28. Jim Ebersberger  jebers@wpa.net
29. David Templeton  davidt@opentext.com
30. Doug Matthews    mathews@uga.edu
31. Bob              rbreazeale-tr250@mailblocks.com
32. John North       jnorth@novagate.com
33. Bill Saidel      saidel@camden.rutgers.edu
34. David Welch      Publicus@earthlink.net
35. Frank Krajewski  frankk@intap.net
36. Mark Macy        pmmacy@att.net
37. John Cyganowski  janah@att.net



Dave Waldorf wrote:
> I got mine from J.C. Whitney more than 10 years ago.  It works wonderfully, if
> you know how to use it!
> 
> It is not designed to power tie rods apart.  If you're cranking on it hard
> enough to strip the threads you're not using it right.  This tool should be
> tightened down on the joint as hard as is practical (i.e. don't strip
> anything), and then tapped with a hammer with gradually increasing force until
> the joint seperates easily or the the tool gets loose and needs retightening.
> 
> At least 4 out of 5 times when I've used this thing it only takes a few taps
> to seperate the joint and I've yet to see it damage a grease seal or boot at
> the joint (try that with a pickle fork!).    It's one of the best $10 tool
> buys I've ever made!   :-)
> 
> --Dave Waldorf




<Prev in Thread] Current Thread [Next in Thread>