triumphs
[Top] [All Lists]

[Fot] Type A OD pressure test

Subject: [Fot] Type A OD pressure test
From: charly at mitchelplumbing.com (Charly Mitchel)
Date: Tue, 6 Mar 2018 11:57:51 -0800
References: <7DF32ACB-8C68-45A3-9654-C743E3FB3C1A@icloud.com> <1967427720.8517669.1520273071794@mail.yahoo.com> <1123716743.11727331.1520335836458@mail.yahoo.com> <003901d3b55a$3503c540$9f0b4fc0$@att.net> <4774C90B-FECF-420A-9343-42AEE8D920F9@gmail.com> <DAD9EECD8E984095A04E4B01039A3E38@Charly> <8611DCE6-95F7-4A94-A0D0-BBD418DF2927@gmail.com>
Not to me it isn't, it's not really proving anything.  Can't tell it it's 
leaking past seals.
Charly Mitchel
TR6 #44
----- Original Message ----- 
  From: J Wagner 
  To: Charly Mitchel 
  Cc: fot at autox.team.net 
  Sent: Tuesday, March 06, 2018 11:40 AM
  Subject: Re: [Fot] Type A OD pressure test


  Makes sense.  Subsequently, is compressed air a viable means of testing seals 
that normally run gear oil?









  On Mar 6, 2018, at 10:17 AM, Charly Mitchel <charly at mitchelplumbing.com> 
wrote:


    I believe the answer is the water molecules are larger than the air 
molecules, which makes them easier to pass through the space.  I think Gore-Tex 
work the same way, lets the fabric breathe, but keeps the water out.
    Not sure why I know this :)
    Charly Mitchel
    TR6 #44
    ----- Original Message ----- 
      From: J Wagner via Fot 
      To: fot at autox.team.net 
      Sent: Tuesday, March 06, 2018 8:03 AM
      Subject: Re: [Fot] Type A OD pressure test


      I?m almost embarrassed to chime in here as I have no expertise on the 
inner workings of a transmission, but  perhaps it?s more of a question than an 
answer.


      I?ve run a lot of PVC irrigation pipe in my day, particularly in the last 
few years landscaping my house.   I?ve noticed that whenever I turn on a new 
system, the air compressed by the incoming water with force it?s way past 
connections of threaded pipe, joined with teflon tape, and take a little water 
with it.  Just when I?m thinking that I?ve failed to tighten the pipe enough, 
the leaking stops once all the air escapes. 


      I suppose it?s a fluid dynamics question.  Will compressed air act 
differently on seals than pressurized oil?


      Maybe the escape of air is as meaningless as it has been in my sprinklers?


      ?Justin

      On Mar 6, 2018, at 6:48 AM, M&M Hado via Fot <fot at autox.team.net> 
wrote:


        Greg,


        Just a couple more thoughts to add to the good suggestions already 
offered. I especially liked Jack?s idea of hand-lapping in the aluminum seats 
with a ball welded to a rod.   


        I?m guessing that most of the air you?re hearing is leaking around the 
outside of the operating valve since air is much more likely to do so than the 
relatively thick 90 weight oil.  Just the fact that only 120 psi of air 
pressure is enough to move the operating pistons tells me that the rest of your 
system is relatively tight.  The normal operating pressure after all is about 
400 psig so you have a lot of ?fat? built into it.  


        One thing that might cause the operating pistons to move with a 
relatively small pressure is having weak or incorrect springs pushing the cone 
clutch rearward.  Be sure you have the so-called ?long? and ?short? ones in the 
right locations,  It?s actually the coil bound length that determines which is 
which.  If you put a long one where a short one will be, it may bind before 
reaching full movement, resulting in the cone clutch not reaching the brake 
ring.  Don?t ask me how I know this.  To check this, I put each spring on a 
threaded rod and run a nut down the rod until the coil binds.  Measure the 
length at that point and the long springs will be about 3/8? longer than the 
short ones.


        Also, the seating of the balls on the aluminum seats in the casing is 
indeed important but it?s also important to have a good seat between the ball 
and tip of the operating valve.  I had a D-type OD that was eating my lunch 
with low operating pressure during engagement and the tip of the valve was 
nicked resulting in a bad seal.  Changing the valve solved the problem.  The 
oil flow is very small in the system so a leak of even the smallest area will 
drop the pressure quite a bit.


        Lastly, you mentioned the ?relief valve? and I?m not sure which valve 
you are referring to since the pressure relief occurs when the accumulator 
piston moves enough to uncover the relief holes back to the sump.  Since you 
only had 120 psi, the accumulator piston would not have moved nearly enough to 
?relieve.?  I?m guessing you were referring to the operating valve.


        Mike Hado


        From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of barry 
rosenberg via Fot
        Sent: Tuesday, March 6, 2018 5:31 AM
        To: Jack Wheeler; Greg Blake via Fot
        Subject: Re: [Fot] Type A OD pressure test


        I used to put the ball in a tap in down with a blunt punch. As the case 
is aluminum and the ball hard steel, it made a very nice seat for itself. This 
can be done without pulling the OD apart. Just pull the plug, spring and little 
plunger.


        Barry


        On Monday, March 5, 2018 5:26 PM, Jack Wheeler via Fot <fot at 
autox.team.net> wrote:


        Hi Greg.  Here is a tip for you.  When I used to rebuild A-Type 
overdrives, I would "lap in" the surface that the ball sits on.  I had a spare 
ball of the correct size, and I welded a small rod to it (about 3/16" diam.).  
Then I put a bit of valve grinding compound on the ball, inserted it down into 
the hole, then turned it back and forth, thus lapping the surface that the ball 
sits on.  This is a tip that Hardy Prentice gave me years ago, when we were 
both racing, and obviously the purpose was to minimize any leakage past the 
ball.  This may be to late in your case, as you would have to do this while the 
unit is apart, so that you can carefully clean all of the grinding compoound 
out of the housing after the lapping.  Maybe this will help you next time.  
Good luck.


        Jack Wheeler



        On Monday, March 5, 2018, 12:12:29 AM EST, Greg Blake via Fot <fot at 
autox.team.net> wrote: 



        All knowing FOT


        Attached is a video of my Type A OD unit ready to bolt up to the 
transmission. I decided to do a pressure test with 120psi of compressed air 
plumbed into the operating vale port. 


        The engagement seems to work well when I move the operating lever. But 
I am concerned about the amount of air that can be heard leaking. I believe it 
is going past the relief valve. Is this abnormal amount of leaking?


        I noticed upon tear down that the nonreturn valve had a 1/4" ball 
instead of the 5/16" this unit should have had. The test you see in the video 
is with a new 5/16" ball. I am sure on a previous rebuild someone mistakenly 
used the later style 1/4". 



        Just wanted opinions before I buttoned this up to the transmission for 
some bench testing. 

        Thanks. 

        Greg

        Sent from my iPhone_______________________________________________
        fot at autox.team.net

        http://www.fot-racing.com

        Donate: http://www.team.net/donate.html
        Archive: http://www.team.net/archive
        Forums: http://www.team.net/forums
        Unsubscribe/Manage: 
http://autox.team.net/mailman/options/fot/jwheeler1947 at yahoo.com



        _______________________________________________
        fot at autox.team.net

        http://www.fot-racing.com

        Donate: http://www.team.net/donate.html
        Archive: http://www.team.net/archive
        Forums: http://www.team.net/forums
        Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/britcars 
at bellsouth.net





        _______________________________________________
        fot at autox.team.net

        http://www.fot-racing.com

        Donate: http://www.team.net/donate.html
        Archive: http://www.team.net/archive
        Forums: http://www.team.net/forums
        Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/4msonset 
at gmail.com





--------------------------------------------------------------------------


      _______________________________________________
      fot at autox.team.net

      http://www.fot-racing.com

      Donate: http://www.team.net/donate.html
      Archive: http://www.team.net/archive
      Forums: http://www.team.net/forums
      Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/charly at 
mitchelplumbing.com


-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180306/56b8214c/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>