- 181. Re: [Healeys] Compression ratio for a fast road 100 (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sat, 15 Jan 2011 01:24:09 +0000
- The 6 cylinder flywheels are 28-29 pounds. Richard Mayor BN7L-466 Vintage Racer Portland, Oregon Mini under reduced peppy! http://autox.team.net/mailman/options/healeys/mayorrichard@hotmail.com _____
- /html/healeys/2011-01/msg00277.html (11,406 bytes)
- 182. [Healeys] Bucket Lifters (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sun, 20 Feb 2011 05:11:40 +0000
- The stock Healey 6 cylinder lifter is a pedestal type of lifter that fills up with oil. It is not the best design for a performance engine. You have to grind or machine a "flat" at the lower part to
- /html/healeys/2011-02/msg00295.html (7,231 bytes)
- 183. Re: [Healeys] Crankshaft Nut (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Tue, 29 Mar 2011 01:24:31 +0000
- The 6 cylinder engines have two different sizes of crankshaft nuts, 1-5/8 and 1-11/16. The cranks themselves are identical. The 1-5/8 may be the size used on the 100-6 engines. I do not know when the
- /html/healeys/2011-03/msg00747.html (9,020 bytes)
- 184. Re: [Healeys] Dual fuel pumps (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sat, 16 Apr 2011 02:47:50 +0000
- I'm not sure if running them in series is the best way to go. Before I went to a single Carter fuel pump in my race car, I used two SU fuel pumps plumbed in parallel for many many years, without any
- /html/healeys/2011-04/msg00372.html (9,354 bytes)
- 185. Re: [Healeys] Air Compressor Lines (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sun, 17 Apr 2011 03:54:06 +0000
- Either pipe dope or teflon tape will work just fine. If it were me I would use the tape. The dope is just messy. FWIW, I plumbed my shop using copper pipe. Richard Mayor BN7L-466 Vintage Racer Portla
- /html/healeys/2011-04/msg00411.html (8,318 bytes)
- 186. Re: [Healeys] Gearbox (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sun, 17 Apr 2011 03:59:48 +0000
- Thick gear box oil ?????? You should use 30W motor oil in your transmission! Richard Mayor BN7L-466 Vintage Racer Portland, Oregon like be wear-pad http://autox.team.net/mailman/options/healeys/mayor
- /html/healeys/2011-04/msg00412.html (10,870 bytes)
- 187. Re: [Healeys] County parts - Engine bearings (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sat, 30 Apr 2011 02:53:51 +0000
- I, and several other Healey 3000 racers, have had very bad results with King bearings sold under the "County" brand. That is why I am the source for ACL bearings for 6 cylinder engines in the USA. AC
- /html/healeys/2011-04/msg00732.html (8,158 bytes)
- 188. Re: [Healeys] smitty 5 speed - type of oil (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Wed, 4 May 2011 01:27:33 +0000
- Whooooa, I'm not an expert here, but -- I think Perry is suggesting you use the kind of oil you put into a differential. Why don't you call the Toyota service department. Or talk to the people at Jif
- /html/healeys/2011-05/msg00069.html (9,033 bytes)
- 189. Re: [Healeys] Engine Stand or Cradle (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Fri, 13 May 2011 03:34:20 +0000
- There are many sizes of 3 wheel engine stands. I also have two 3 wheel engine stands. One is of marginal size and strength. That is why I purchased the second stand for my Healey 6 cylinder engines.
- /html/healeys/2011-05/msg00179.html (8,859 bytes)
- 190. [Healeys] Thread size on pipe from oil pump by pass (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Mon, 16 May 2011 02:25:19 +0000
- There is a pipe that screws into the bottom of the block on 6 cylinder engines. It is the oil discharge pipe from the oil pump pressure relief valve. At first impression it appears to be an American
- /html/healeys/2011-05/msg00262.html (7,252 bytes)
- 191. [Healeys] Access door in surround for Webers (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Mon, 16 May 2011 02:34:15 +0000
- Is there anyone on the list that could provide me with a template of the "works" door that was cut out of the front surround on the Rallye cars to access the Weber carburetors? Richard Mayor BN7L-466
- /html/healeys/2011-05/msg00263.html (6,559 bytes)
- 192. Re: [Healeys] Healey 3000-bore size for main and rod bearing housing (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Fri, 20 May 2011 01:18:45 +0000
- If your machine shop doesn't know this, then you should go (I mean run) somewhere else. Richard Mayor BN7L-466 Vintage Racer Portland, Oregon know http://autox.team.net/mailman/options/healeys/mayorr
- /html/healeys/2011-05/msg00384.html (8,692 bytes)
- 193. [Healeys] Question for Racers - #6 cylinder heating problem? (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Tue, 24 May 2011 02:09:39 +0000
- Over the years I have seen a number of photos of British and European Austin-Healey race car engines that use a hose from the water heater valve at the rear of the cylinder head that is connected to
- /html/healeys/2011-05/msg00515.html (7,520 bytes)
- 194. Re: [Healeys] Healeys] Start-up, oil filters, (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Thu, 26 May 2011 01:53:07 +0000
- What is "nitrate" and how do you "nitrate" a camshaft. It is usually the case, but not always, that the lifters go away before the camshaft. I believe that lifters are usually chilled iron - camshaf
- /html/healeys/2011-05/msg00578.html (8,050 bytes)
- 195. Re: [Healeys] Healeys] Start-up, oil filters, and rebuilt engines (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Fri, 27 May 2011 01:33:11 +0000
- I know what "nitriding" is. And it will not solve the problem of wiping out cam lobes or lifters or both. Richard Mayor BN7L-466 Vintage Racer Portland, Oregon engines http://autox.team.net/mailman/o
- /html/healeys/2011-05/msg00604.html (11,431 bytes)
- 196. Re: [Healeys] Canadian 'Vintage' race Healey for Auction (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Fri, 3 Jun 2011 01:42:39 +0000
- Check out the roll bar on the driver's side. How does one get in or out? I'd hate to be in this death trap if it ever caught on fire during a race. Richard Mayor BN7L-466 Vintage Racer Portland, Oreg
- /html/healeys/2011-06/msg00056.html (9,889 bytes)
- 197. [Healeys] County brand oil pump s**t (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sun, 12 Jun 2011 05:50:02 +0000
- A few months ago I bought a brand new oil pump for a fresh race motor for the 2011 season. It turned out to be a "County" oil pump. The bag contained a flyer that said something like "do not open thi
- /html/healeys/2011-06/msg00299.html (7,973 bytes)
- 198. [Healeys] Firewall material (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sat, 25 Jun 2011 02:50:30 +0000
- Dear Listmates, What is that product that Home Depot sells that is similar to the original white asbestos firewall material. I know this has been discussed on the list a number of times in the past.
- /html/healeys/2011-06/msg00756.html (6,915 bytes)
- 199. Re: [Healeys] Tri-carb Trivia (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Sun, 10 Jul 2011 03:52:38 +0000
- This is the correct throttle linkage. Richard Mayor BN7L-466 Vintage Racer Portland, Oregon http://www.hawkins.info/1962 http://autox.team.net/mailman/options/healeys/mayorrichard@hotmail.com _______
- /html/healeys/2011-07/msg00324.html (8,788 bytes)
- 200. Re: [Healeys] timing chain (score: 1)
- Author: richard mayor <mayorrichard@hotmail.com>
- Date: Fri, 22 Jul 2011 00:28:00 +0000
- As far as I can determine, ALL of the usual sources for Healey parts sell the cheap timing chains ($10.00) with the "County" label. Another common brand is/was Rolon made in India also selling for ab
- /html/healeys/2011-07/msg00688.html (8,927 bytes)
This search system is powered by
Namazu