- 1. Re: [TR] Oil pump re-assembly 4 cyl. TR motor (score: 1)
- Author: Alan & Lyn Dunscombe <dunscomb@chch.planet.org.nz>
- Date: Fri, 30 Nov 2018 23:27:47 +1300
- This is a multi-part message in MIME format. --==1563276271488425297== boundary="--070100090507060108050001" This is a multi-part message in MIME format. --070100090507060108050001 Content-Transfer-E
- /html/triumphs/2018-11/msg00157.html (40,310 bytes)
- 2. Re: [TR] Oil pump re-assembly 4 cyl. TR motor (score: 1)
- Author: TERRY SMITH <terryrs@comcast.net>
- Date: Fri, 30 Nov 2018 09:41:56 -0500 (EST)
- --==8119917150561200008== boundary="--=_Part_214819_861173081.1543588917215" --=_Part_214819_861173081.1543588917215 Content-Transfer-Encoding: 7bit Hi, Alan. I didn't think so but couldn't remember
- /html/triumphs/2018-11/msg00161.html (13,762 bytes)
- 3. Re: [TR] Oil pump re-assembly 4 cyl. TR motor (score: 1)
- Author: "Randall" <TR3driver@ca.rr.com>
- Date: Fri, 30 Nov 2018 07:03:08 -0800
- No gasket, I don't use any sealer. Do check that the surfaces are perfectly flat, though. Sometimes even new components aren't. I think 12 ftlbs is a reasonable torque value; but I don't have a fact
- /html/triumphs/2018-11/msg00162.html (9,661 bytes)
- 4. Re: [TR] Oil pump re-assembly 4 cyl. TR motor (score: 1)
- Author: "Andrew Uprichard" <auprichard@uprichard.net>
- Date: Fri, 30 Nov 2018 11:09:23 -0500
- One additional point. I once rebuilt an engine, but couldn't get good oil pressure. As I had re-used the original oil pump, I pulled the sump to see if the problem was a faulty oil pump. It was then
- /html/triumphs/2018-11/msg00165.html (10,932 bytes)
- 5. Re: [TR] Oil pump re-assembly 4 cyl. TR motor (score: 1)
- Author: "Jerry Van Vlack" <jerryvv@roadrunner.com>
- Date: Fri, 30 Nov 2018 11:18:05 -0500
- This is a multi-part message in MIME format. --==4508464468351745597== boundary="--=_NextPart_000_0918_01D4889E.5D884910" This is a multi-part message in MIME format. --=_NextPart_000_0918_01D4889E.5
- /html/triumphs/2018-11/msg00166.html (14,576 bytes)
- 6. Re: [TR] Oil pump re-assembly 4 cyl. TR motor (score: 1)
- Author: Alan & Lyn Dunscombe <dunscomb@chch.planet.org.nz>
- Date: Sun, 02 Dec 2018 11:33:32 +1300
- thanks everyone for your prompt replies to my post, especially Randall as always, just the info I needed much appreciated Alan TS 3612 down in New Zealand ** triumphs@autox.team.net ** Archive: http:
- /html/triumphs/2018-12/msg00002.html (68,490 bytes)
This search system is powered by
Namazu