Mail Archive Search: <+from:kidjoevid@yahoo.com>

Results:

References: [ +from:kidjoevid@yahoo.com: 89 ]

Total 89 documents matching your query.

81. [Spridgets] Distributor drive spindle install (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Fri, 8 Aug 2008 05:13:00 -0700 (PDT); Is there something special or critical in how the drive spindle is inserted for the distibutor? I'm using a longish bolt to insert it into the hole, kinda feeling my way intil it slips into the hole; /html/spridgets/2008-08/msg00247.html (7,196 bytes)
82. Re: [Spridgets] Distributor drive spindle install (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Fri, 8 Aug 2008 13:40:46 -0700 (PDT); Duhhh...what retainer? - _______________________________________________ Support Team.Net http://www.team.net/donate.html http://www.team.net/archive http://autox.team.net/mailman/listinfo/spridgets; /html/spridgets/2008-08/msg00266.html (8,684 bytes)
83. Re: [Spridgets] Distributor drive spindle install (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Fri, 8 Aug 2008 14:47:16 -0700 (PDT); OK. I was thinking I had overlooked a spring clip or something... _______________________________________________ Support Team.Net http://www.team.net/donate.html http://www.team.net/archive http://a; /html/spridgets/2008-08/msg00268.html (10,908 bytes)
84. [Spridgets] Can't get new engine to fire (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Fri, 8 Aug 2008 14:54:38 -0700 (PDT); I've been fighting with this off and on for months. I think I've checked everything. What else should I look for? Distributor (124 Ignition Dizzy) 1. Drive spindle is seated good, slot is aligned 2:0; /html/spridgets/2008-08/msg00269.html (7,737 bytes)
85. [Spridgets] Can't get new engine to fire cont. (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Sun, 10 Aug 2008 07:31:49 -0700 (PDT); OK - I tried using a plug wire straight to #1 from coil. It did not fire. I pulled the plug and turned it over, and there was spark at the gap. I'll try a new coil. But one question - could my engine; /html/spridgets/2008-08/msg00318.html (9,501 bytes)
86. [Spridgets] New engine tried to run;dizzy clamp (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Sun, 10 Aug 2008 14:58:08 -0700 (PDT); Thanks for all the advice on static timing - I got my new engine to run about 3 seconds before the dizzy slipped about 15 degrees - the clamp was too loose. I tried it with the clamp even tighter but; /html/spridgets/2008-08/msg00329.html (7,451 bytes)
87. [Spridgets] Freakin' distributor (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Sat, 6 Sep 2008 10:58:45 -0700 (PDT); I cannot get my distributor (in my new engine) to stay cinched down. I got a new clamp from Moss, but that doesn't help. I can get timing set rough, then after 5 seconds of run time it slips and rota; /html/spridgets/2008-09/msg00192.html (7,486 bytes)
88. [Spridgets] wiring to coil (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Sat, 20 Sep 2008 10:34:47 -0700 (PDT); I'm double-checking myself on the wiring for my coil. Is this correct? There are two leads that have always been there - a positive to the + side and a negative to the - side. My new dizzy has just o; /html/spridgets/2008-09/msg00817.html (7,475 bytes)
89. Re: [Spridgets] wiring to coil (score: 1): Author: Joe Lansing <kidjoevid@yahoo.com>; Date: Sat, 20 Sep 2008 14:05:40 -0700 (PDT); I get 12 volts on either side. The points are brand new. I still get no spark. I actually get 12 volts at the primary coil wire center post. _______________________________________________ Support Te; /html/spridgets/2008-09/msg00823.html (9,634 bytes)

Current List: 81 - 89
Page: [1] [2] [3] [4] [5]