- 1. MG Parts (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Tue, 30 Jan 2001 23:15:38 -0500
- Ok all !! I have just come into a small warehouse of MG parts. Chrome, badges, engine parts, tranny parts, engines, parts parts parts. If there is a need and I can help drop a line and I'll look to s
- /html/mgs/2001-01/msg01075.html (6,366 bytes)
- 2. vibrations (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Sun, 31 Dec 2000 10:44:47 -0500
- Well the saga continues:) I removed the shifter boot yesterday, preparing to remove the eng and trans and found all 4 bolts completely backed off on the yoke for the drive shaft. However after tighte
- /html/mgs/2000-12/msg01104.html (7,286 bytes)
- 3. Re: vibrations (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Sun, 31 Dec 2000 11:40:11 -0500
- The engine mounts "seem" ok as I can not rock the engine from side to side, I have noticed that the rear trans mounts are at the bottom of the elongated hole. These are the round mounts. Is there a a
- /html/mgs/2000-12/msg01108.html (6,674 bytes)
- 4. fuel guage wo's (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Mon, 6 Nov 2000 23:42:03 -0500
- Can anyone remember the thread that talked about a home built fuel gauge Dang I got to remember to book mark this kind of stuff ! :) Thanks all ! Mark H 79 Midget
- /html/mgs/2000-11/msg00263.html (6,405 bytes)
- 5. Re: Wire Feed Welders (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Mon, 27 Nov 2000 08:51:30 -0500
- I went through the same problem with the front right fender repair on my 79 midget. I found that a small dia. wire (.25) and low power was part of the answer. I also had to keep the nozzle almost par
- /html/mgs/2000-11/msg01011.html (6,948 bytes)
- 6. Webbers (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Tue, 3 Oct 2000 21:40:39 -0400
- Can anyone tell me what the correct jet #s and Venturi #s are for a Webber down draft carb. DCOE ?? Also where I might get a good illustrated parts breakdown for the same carb.
- /html/mgs/2000-10/msg00138.html (6,480 bytes)
- 7. midget 79 (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Sun, 8 Oct 2000 11:18:08 -0400
- I own a 79 Midget with what is suppose to be a 1500 here is the problem, the engine stumbles and surges when driving at road speeds. that is any speed I try to hold steady. the engine timeing is rock
- /html/mgs/2000-10/msg00453.html (7,482 bytes)
- 8. Alignment (score: 1)
- Author: "Mark Hardin" <markha1@earthlink.net>
- Date: Sat, 28 Oct 2000 12:30:43 -0400
- well here I am again "DNO" At looking at my front end I am also wondering how exactly caster and camber would be adjusted. I have original lever arm shocks, and as it looks to me there is no way to r
- /html/mgs/2000-10/msg01328.html (7,044 bytes)
This search system is powered by
Namazu