- 121. [Spridgets] Small questions (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Wed, 17 Sep 2008 10:35:30 -0400
- 1. Should the rebound straps be short enough to prevent the drive shaft from rubbing on the frame when the car is on stands? How much clearance? 2. To stop leaking, I had to tighten one front brake b
- /html/spridgets/2008-09/msg00716.html (6,898 bytes)
- 122. Re: [Spridgets] Small questions (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Wed, 17 Sep 2008 13:46:36 -0400
- Cancel this one. It turned out that the drive shaft was pulled out of the transmission when I replaced the rear end. I assume it will fit better when it is properly attached. Cars are like that. Whi
- /html/spridgets/2008-09/msg00728.html (7,749 bytes)
- 123. Re: [Spridgets] Small questions (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Wed, 17 Sep 2008 20:28:16 -0400
- Thanks to all for good advice. As usual, knowledge makes everything easier. Michael Rowe '74 Midget Long Island, NY _______________________________________________ Support Team.Net http://www.team.ne
- /html/spridgets/2008-09/msg00751.html (7,044 bytes)
- 124. Re: [Spridgets] Spridget Covers (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Wed, 17 Sep 2008 20:45:52 -0400
- I saw a comment somewhere about elastic at the bottom forming pockets that collected water and rusted out the bottom corners of the car. Perhaps some care should be taken to provide drainage for cond
- /html/spridgets/2008-09/msg00755.html (7,496 bytes)
- 125. Re: [Spridgets] Spridget Covers (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Thu, 18 Sep 2008 10:01:31 -0400
- Depends on how the cover fits. You just need to make sure that no pockets form anywhere. It doesn't matter how you do that, so long as it works. Also, the less touching of the body the better. Conde
- /html/spridgets/2008-09/msg00778.html (8,275 bytes)
- 126. [Spridgets] 1981 Mazda RX7 Rotary Engine (Bay) (score: 1)
- Author: mdrowe@optonline.net
- Date: Tue, 23 Sep 2008 00:51:34 GMT
- mdrowe@optonline.net has forwarded you this craigslist.org posting. Please see below for more information. 1981 Mazda RX7 Rotary Engine I've got an 81 Mazda RX7 Rotary Engine in my garage. An old boy
- /html/spridgets/2008-09/msg00874.html (7,620 bytes)
- 127. [Spridgets] economics of toys (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Thu, 25 Sep 2008 22:26:12 -0400
- The economic "melt-down" is likely to increase the number of Spridgets and other toys entering the market. What are the list's opinions on the quality of the cars most likely to become available? Wil
- /html/spridgets/2008-09/msg00951.html (7,274 bytes)
- 128. Re: [Spridgets] economics of toys (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Fri, 26 Sep 2008 13:08:00 -0400
- If we get Sarah Palin, it doesn't matter. God will take care of everything. _______________________________________________ Support Team.Net http://www.team.net/donate.html http://www.team.net/archiv
- /html/spridgets/2008-09/msg00980.html (9,687 bytes)
- 129. [Spridgets] Pittsburgh (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Fri, 26 Sep 2008 13:37:11 -0400
- Please remind me who lives in Pittsburgh, PA. Michael Rowe '74 Midget Long Island, NY _______________________________________________ Support Team.Net http://www.team.net/donate.html http://www.team.
- /html/spridgets/2008-09/msg00981.html (7,118 bytes)
- 130. [Spridgets] Disk Brake sticking (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Tue, 30 Sep 2008 21:06:08 -0400
- One of my front brake calipers is sticking a little, not retracting properly. Will a little cleaning and polishing fix this, or must I rebuild it? The calipers are used of unknown previous condition.
- /html/spridgets/2008-09/msg01113.html (7,217 bytes)
- 131. [Spridgets] No clutch (score: 1)
- Author: Michael Rowe <mdrowe@optonline.net>
- Date: Wed, 01 Oct 2008 15:29:37 -0400
- New plate and bearing. Slave bleed. Hydraulics *seem* to be OK, but the slave piston travel is only 1/4". How much travel should the clutch need? Is this a leaky MC? Michael Rowe '74 Midget Long Isla
- /html/spridgets/2008-10/msg00021.html (6,764 bytes)
This search system is powered by
Namazu