Harbor Freight in the US has a non-contact laser thermometer for sale. Anyone used any of these types with good results? They are on sale for $30 Sujit -- Sujit Roy, Realtor Keller Williams Realty, C
Can anyone recommend a good liquid type rust remover? I'd like to soak some Stag parts in a bath. There are some types where you soak them in a bath and then wash the stuff off, I'm not looking for t
Thanks this is all good information. How would I clean the very small parts with the reverse plating method? It would be difficult and time consuming to do one part at a time. Back in the UK I used a
I'm cleaning some rear brake drum cylinders for a car Stag I someday plan to get back on the road. What can I apply to them to stop them rusting and the seals from going hard? They are currently off
I have a vacuum advance/retard unit for a '71 Stag which needs rebuilding Sujit -- Sujit Roy, Realtor Keller Williams Realty, Cupertino, CA (408) 839-8359 roysrealty.com
I'd like a kit if possible where the temp sender part can bolt into the block/head Sujit -- Sujit Roy, Realtor Keller Williams Realty, Cupertino, CA (408) 839-8359 roysrealty.com
Thanks. It's for a Stag. I want to swap out the electrical one for a bulb type. Anyone know what is the typical thread used for the bit that goes in the block? They have this listed. * *Supplied with
Can any one recommend one for the old job. Harbor Freight seems to carry inexpensive ones. What should I look for in one? Thanks, Sujit -- Sujit Roy, Realtor Keller Williams Realty, Cupertino, CA (40
I'm using a standard battery charger to charge my battery. It's been on for about 12 hours and the meter needle is sitting between 1/2 Full and Full. It doesn't read FULL. When charged with the batte
I'm exploring poly bushes for my Stag. From memory the Superflex brand need periodic re-greasing. Is this still the case? Are there other poly vendors worth recommending that are fit and forget. Some
I've got a great deal on a MIG welder from Sears/ Craftsman. It came with a mickey mouse hand-held visor. I'd like to get a good one. What should I look for? For ones that say auto-darkening should I
Does anyone have some they want to sell? The '73 Fed Stag uses the same one. Regards, Sujit -- Sujit Roy, Realtor Keller Williams Realty, Cupertino, CA (408) 839-8359
Last check. Last oil change was 3 years ago, but only driven about 800 miles. Each trip very short runs. Sujit '71 Stag -- Sujit Roy, Realtor Keller Williams Realty, Cupertino, CA (408) 839-8359 roys
Every web search search I do, points to a place in the UK. Since these bushes are made in Australia. Is three a distributor / reteller out there that will ship to the USA? Sujit -- Sujit Roy, Realtor
The Stag has 2 special machined alignment bell housing bolts. I'm assuming the TR6 and other Triumph used similar. Are these available anywhere? Sujit -- Sujit Roy Cupertino, California https://trium
Sujit -- Sujit Roy Cupertino, California https://triumphstagblog.wordpress.com/ -- next part -- An HTML attachment was scrubbed... URL: <http://autox.team.net/pipermail/triumphs/attachments/20180807/
For those of you how have a '71 Stag, can you please help me answer the following two questions: On your '71 Stag. Do you have two 2 top port carbon canisters or do you have one 3 top port canister?
Due to tight space, I can't put a socket on the end of a torque wrench, but I can put a small Craftsman crow foot on the end. If I do this, by what factor should I add or remove from the specified to