Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[6pack\]\s+trailing\s+arm\s+studs\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[6pack\]\s+trailing\s+arm\s+studs\s*$/: 6 ]

Total 6 documents matching your query.

1. [6pack] trailing arm studs (score: 1): Author: Jimandruthhome@aol.com; Date: Mon, 20 Aug 2007 17:45:29 EDT; I know this issue has come up before, but I always thought, "never happen to me" so I didn't pay close attention. Well, it happened to me, driving down the Garden State Parkway headed for a week at; /html/6pack/2007-08/msg00184.html (7,608 bytes)
2. RE: [6pack] trailing arm studs (score: 1): Author: "Navarrette, Vance" <vance.navarrette@intel.com>; Date: Tue, 21 Aug 2007 13:50:23 -0700; Dunno if you got a reply or not. So here goes... Let me say that I have not dealt with this personally, other than to disassemble my trailing arms and rebuild the hubs and replace U-Joints. The stud; /html/6pack/2007-08/msg00187.html (9,901 bytes)
3. [6pack] trailing arm studs (score: 1): Author: "Philip E. Barnes" <peb3@cornell.edu>; Date: Mon, 5 May 2008 09:22:33 -0400; What is the threading of the holes tapped in the trailing arm to secure the hub? I can't recall if it's 1/4-20 or 1/4-28. I want to put in Heli-coils, but I don't want to get the wrong bits. TIA, --; /html/6pack/2008-05/msg00058.html (7,124 bytes)
4. Re: [6pack] trailing arm studs (score: 1): Author: "Bob Danielson" <75TR6@tr6.danielsonfamily.org>; Date: Mon, 5 May 2008 10:32:49 -0400; They're 5/16-24. I didn't use Heli-coil due to the need for their special drill. I went to McMaster Carr and got Keen-Serts, though McMaster doesn't use their trade name. Do a search on "key locking; /html/6pack/2008-05/msg00061.html (8,811 bytes)
5. Re: [6pack] trailing arm studs (score: 1): Author: Robert Lang <lang@isis.mit.edu>; Date: Mon, 5 May 2008 11:08:27 -0400 (EDT); Stock 5/16-24 You can convert to 5/16-18, but you have to buy new studs and you _may_ have to grind them down a bit to clear the hub flange. I've used studs that are course threat on one end and fine; /html/6pack/2008-05/msg00068.html (7,697 bytes)
6. Re: [6pack] trailing arm studs (score: 1): Author: "Navarrette, Vance" <vance.navarrette@intel.com>; Date: Mon, 5 May 2008 08:50:43 -0700; No need to buy a special drill bit. I have a drill bit set that goes in 1/64" (1/16 through 3/8) and I just use the closest undersize drill that I have. Aluminum is so soft that the tap will remove; /html/6pack/2008-05/msg00070.html (8,355 bytes)

Current List: 1 - 6
Page: [1]