Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Alpines\]\s+Clutch\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Alpines\]\s+Clutch\s*$/: 8 ]

Total 8 documents matching your query.

1. [Alpines] Clutch (score: 1): Author: Łauri <lehtinen.lauri@kolumbus.fi; Date: Wed, 21 Jan 2009 14:20:47 +0200; I have to build a new clutch for my 1725 series 4. My problem is, I have to buy either plate or assembly or both, and thrust bearing anyway. Do you know which cars used same clutch parts? 15 years a; /html/alpines/2009-01/msg00013.html (7,340 bytes)
2. Re: [Alpines] Clutch (score: 1): Author: Mary and Ron Tebo <mrtebo@shaw.ca>; Date: Thu, 22 Jan 2009 06:01:36 -0700; As I recall, most clutches were made by Borg and Beck, and had parts that interchanged with MG clutches by the same mfgr. Below is some info that may help. If you need more specific info, let me kno; /html/alpines/2009-01/msg00015.html (9,230 bytes)
3. Re: [Alpines] Clutch (score: 1): Author: Mary and Ron Tebo <mrtebo@shaw.ca>; Date: Thu, 22 Jan 2009 06:10:47 -0700; Here is what you wanted from later in that thread Ron Tebo Mike, That information has a lot of errors in it for the Alpine. Here is the truth on Alpine flywheels/clutches/splines/assembly pins/clutch; /html/alpines/2009-01/msg00016.html (9,400 bytes)
4. Re: [Alpines] Clutch (score: 1): Author: Łauri <lehtinen.lauri@kolumbus.fi; Date: Fri, 23 Jan 2009 01:07:18 +0200; I will absolutely not put that 8.5" flywheel unit back again, as I have 270 deg cam in. Reground cam - with untrimmed Zenith-Strombergs and old mechanical ignition - was so revolutionary change in th; /html/alpines/2009-01/msg00017.html (8,261 bytes)
5. Re: [Alpines] Clutch (score: 1): Author: "Carl McLelland" <carlynneracing@sbcglobal.net>; Date: Thu, 22 Jan 2009 15:53:02 -0800; Take the flywheel to a machine shop and have it lightened, balanced, and matched to a modern pressure plate and clutch disk to match the input shaft from the transmission. The throwout bearing should; /html/alpines/2009-01/msg00018.html (9,049 bytes)
6. Re: [Alpines] Clutch (score: 1): Author: "Wiencek, Thomas" <wiencek@anl.gov>; Date: Fri, 23 Jan 2009 09:34:12 -0600; There is company in Australia making dual weber side draft manifolds . Do a search on Redline manifolds PART NO. 12-3040 Hunter, Minx, Sunbeam Alpine, Manifold designed to accept 2 x 40 DCOE Weber Ca; /html/alpines/2009-01/msg00019.html (9,833 bytes)
7. Re: [Alpines] Clutch (score: 1): Author: Moto <mototron@optonline.net>; Date: Fri, 23 Jan 2009 19:09:48 -0500; I had The Ram Clutch Corp make a Aluminium flywheel for my Series II They did a great job It cost me $600 but it might be cheaper now that they have blueprints I have a Holbay dual weber manifold if; /html/alpines/2009-01/msg00020.html (11,831 bytes)
8. Re: [Alpines] Clutch (score: 1): Author: Łauri <lehtinen.lauri@kolumbus.fi; Date: Sat, 24 Jan 2009 11:56:52 +0200; I found Pierce manifolds at net, but I did not find their prices, I must send an email to them. One possibility might be to weld together a manifold using either steel or starting with a series 1-2 a; /html/alpines/2009-01/msg00021.html (7,254 bytes)

Current List: 1 - 8
Page: [1]