Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Bricklin\]\s+Pinion\s+nut\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Bricklin\]\s+Pinion\s+nut\s*$/: 7 ]

Total 7 documents matching your query.

1. [Bricklin] Pinion nut (score: 1): Author: "Larry Ankeny" <lvphotogroup@cox.net>; Date: Fri, 8 Jul 2011 16:55:37 -0700; I am trying to get the pnion nut off of the rear axle so that i can replace the pinion seal. Does anyone know if this has a reverse thread? I have tryed everything to bust this loose. an impact gun,; /html/bricklin/2011-07/msg00001.html (6,341 bytes)
2. Re: [Bricklin] Pinion nut (score: 1): Author: "Greg Schroeder" <gschroeder@comcast.net>; Date: Fri, 8 Jul 2011 22:10:33 -0500; It is designed to only go on once. Once it is removed it is recommended to be replaced. I removed mine with an impact air wrench. It took a while to get it removed. One thing at this point you need; /html/bricklin/2011-07/msg00002.html (8,643 bytes)
3. Re: [Bricklin] Pinion nut (score: 1): Author: "Larry Ankeny" <lvphotogroup@cox.net>; Date: Fri, 8 Jul 2011 21:08:37 -0700; I was going to count the turns. My impact gun has 450 foot pounds of I can't imagine I need more then that. I thinking about hooking up a come-along to a breaker bar connected to a socket. Next will; /html/bricklin/2011-07/msg00003.html (9,702 bytes)
4. Re: [Bricklin] Pinion nut (score: 1): Author: "Greg Schroeder" <gschroeder@comcast.net>; Date: Fri, 8 Jul 2011 23:34:03 -0500; I believe mine is up to 750 ft/lbs. and it still took a while. Try penetrating fliud like PB blaster or Liquid Wrench. It is in a bad position so a long breaker bar will not work to well unless the e; /html/bricklin/2011-07/msg00004.html (10,146 bytes)
5. Re: [Bricklin] Pinion nut (score: 1): Author: D Walker <treefrogno9@webtv.net>; Date: Sat, 09 Jul 2011 09:49:27 GMT; The torque on the pinion nut can be any amount. Why you should take a torque reading before you take the nut off is to reset the drag force between the pinion bearings. You will need to use a new cru; /html/bricklin/2011-07/msg00005.html (11,777 bytes)
6. Re: [Bricklin] Pinion nut (score: 1): Author: "Rick at High Tech Coatings" <rick@hightechcoatings.com>; Date: Sat, 9 Jul 2011 08:40:48 -0400; the torque they talk about measuring is the torque it takes to turn the rear end, usually measured in inch pounds It is best measured with the drums removed. if you get the drag/torque close to the s; /html/bricklin/2011-07/msg00006.html (9,269 bytes)
7. Re: [Bricklin] Pinion nut (score: 1): Author: "Greg Schroeder" <gschroeder@comcast.net>; Date: Sat, 9 Jul 2011 08:22:30 -0500; The torque reading before removal is from the 1974 AMC Technical Reference manual. This is the only time I have seen a reference like this in the manual. All the other torque settings are listed in t; /html/bricklin/2011-07/msg00007.html (12,826 bytes)

Current List: 1 - 7
Page: [1]