Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Fot\]\s+remote\s+clutch\s+bleeder\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Fot\]\s+remote\s+clutch\s+bleeder\s*$/: 7 ]

Total 7 documents matching your query.

1. [Fot] remote clutch bleeder (score: 1): Author: Tony Drews <tony@tonydrews.com>; Date: Sun, 25 Apr 2010 14:48:00 -0500; Probably interference between the intake and exhaust manifold didn't let the intake manifold seal to the head. Perhaps the new header flange needs "adjustment"? Been there! Clark Clark W. Nicholls 19; /html/fot/2010-04/msg00238.html (9,516 bytes)
2. Re: [Fot] remote clutch bleeder (score: 1): Author: "RACER BUD" <budscars@comcast.net>; Date: Sun, 25 Apr 2010 12:52:59 -0700; Hey Steve Could you run a length of braided brake line from the Clutch slave cyl with a speed bleeder on one end? ~Steve Amici, I've gone brain dead today! I want to rig a remote bleed point for the; /html/fot/2010-04/msg00240.html (11,667 bytes)
3. Re: [Fot] remote clutch bleeder (score: 1): Author: Gt6steve@aol.com; Date: Sun, 25 Apr 2010 16:08:06 EDT; I'm sure chris kantarjiecpv will chime in, but iirc, he ran a length of braided hose up the firewall to a fitting. _______________________________________________ fot@autox.team.net http://www.fot-ra; /html/fot/2010-04/msg00241.html (6,548 bytes)
4. Re: [Fot] remote clutch bleeder (score: 1): Author: "Clark W. Nicholls" <cwnfot@gmail.com>; Date: Sun, 25 Apr 2010 16:08:30 -0400; Thanks, Bob & others who sent comments. One idea was to get an oversize stud, at least on one end, and helicoil at the top of the block and use a short stud. I wouldn't want to enlarge the hole in th; /html/fot/2010-04/msg00242.html (7,697 bytes)
5. Re: [Fot] remote clutch bleeder (score: 1): Author: Steven Belfer <colordog.1@earthlink.net>; Date: Sun, 25 Apr 2010 16:22:46 -0700; I think I'd try a bottoming tap first. You'd have to make a super long one, but that's not too hard. Maybe drop a thin pilot in and drill a little deeper. The pilot would keep the drill from thinning; /html/fot/2010-04/msg00244.html (8,013 bytes)
6. Re: [Fot] remote clutch bleeder (score: 1): Author: Justin Wagner <jmwagner@greenheart.com>; Date: Sun, 25 Apr 2010 19:56:58 -0700; Whatever line you ran up from the slave would need an end with the proper taper fitting to "terminate" the line. Maybe not too tough.. But if Ted S has a setup, maybe it's simpler (aka cheaper) than; /html/fot/2010-04/msg00251.html (8,950 bytes)
7. Re: [Fot] remote clutch bleeder (score: 1): Author: "Tim Murphy" <timmurph@fastbytes.com>; Date: Sun, 25 Apr 2010 22:00:54 -0500; Truth be told, you could probably clean the hole out really good, coat the stud liberally with JB weld, pump the hole full and call it good. It would probably hold until the heat death of the univers; /html/fot/2010-04/msg00252.html (11,010 bytes)

Current List: 1 - 7
Page: [1]