Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Healeys\]\s+Trany\s+Noise\s+Question\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Healeys\]\s+Trany\s+Noise\s+Question\s*$/: 7 ]

Total 7 documents matching your query.

1. [Healeys] Trany Noise Question (score: 1): Author: "Mark LaPierre" <lapierrem@sbcglobal.net>; Date: Tue, 20 Oct 2009 20:20:37 -0400; This is no doubt a very tough question to answer but any ideas would be Rebuilt, 28% O/D transmission. Everything works well, However. I am getting a noticeable clunk, clunk, clunk coming from the O/; /html/healeys/2009-10/msg00724.html (7,702 bytes)
2. Re: [Healeys] Trany Noise Question (score: 1): Author: "Rich C" <richchrysler@quickclic.net>; Date: Tue, 20 Oct 2009 21:29:12 -0400; Rule out the U joints first. Then...bad bearing in o/d or more likely disintegrated o/d thrust washer(s) Rich Chrysler _______________________________________________ Support Team.Net http://www.team; /html/healeys/2009-10/msg00728.html (8,966 bytes)
3. Re: [Healeys] Trany Noise Question (score: 1): Author: "Greg Lemon" <glemon@neb.rr.com>; Date: Tue, 20 Oct 2009 20:50:42 -0500; Long shot, but when I replaced the U joints on my 100 I did not get one of the retaining rings fully seated and so the driveshaft was rotating slightly out of round and I got noise and vibration that; /html/healeys/2009-10/msg00732.html (7,359 bytes)
4. Re: [Healeys] Trany Noise Question (score: 1): Author: Oudesluys <coudesluijs@chello.nl>; Date: Wed, 21 Oct 2009 08:04:59 +0200; Most likely the UV joint. Remove driveshaft to check and run the engine/gearbox through its gears. Noise gone: drive shaft UV joint, noise not gone: expensive! Kees Oudesluijs NL Mark LaPierre schree; /html/healeys/2009-10/msg00749.html (8,767 bytes)
5. Re: [Healeys] Trany Noise Question (score: 1): Author: David Nock <healeydoc@sbcglobal.net>; Date: Wed, 21 Oct 2009 08:18:44 -0700; Check the driveshaft clearance to the seat belt bolts and also the hand brake cable.. They are very close when the car is up on stands and running. David Nock British Car Specialists Stockton Ca 9520; /html/healeys/2009-10/msg00768.html (9,256 bytes)
6. Re: [Healeys] Trany Noise Question (score: 1): Author: "Tracy Drummond" <bighealey@charter.net>; Date: Wed, 21 Oct 2009 09:39:40 -0700; Check the brake cable, mine started rubbing against the drive shaft yoke once long ago in a heavy downpour. Remember putting cards in bicycle spokes to make an engine noise? Kinda like that only real; /html/healeys/2009-10/msg00772.html (7,508 bytes)
7. Re: [Healeys] Trany Noise Question (score: 1): Author: John Harper <ah@jharper.demon.co.uk>; Date: Fri, 30 Oct 2009 14:07:29 +0000; Did you by any chance separate the drive shaft by sliding it off the splines? If you did it is possible to get the drive shaft out of phase. To be correct there are two small pointers on the fixed a; /html/healeys/2009-10/msg01000.html (8,752 bytes)

Current List: 1 - 7
Page: [1]