Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Spridgets\]\s+Thread\s+Locker\s+on\s+Head\s+Studs\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Spridgets\]\s+Thread\s+Locker\s+on\s+Head\s+Studs\s*$/: 6 ]

Total 6 documents matching your query.

1. [Spridgets] Thread Locker on Head Studs (score: 1): Author: rrengineer@dslextreme.com; Date: Wed, 8 Aug 2007 11:07:22 -0700 (PDT); I am getting ready to put the head on my BN2 engine and wondered if any of you guys put anything on the threads of the head studs that you screw into the block. An engine builder friend of mine recom; /html/spridgets/2007-08/msg00066.html (7,516 bytes)
2. Re: [Spridgets] Thread Locker on Head Studs (score: 1): Author: "David Lieb" <dbl@chicagolandmgclub.com>; Date: Wed, 8 Aug 2007 13:14:58 -0500; My understanding is that you will not get an accurate torquing of the head unless they are lubricated. Otherwise, the torque figure is NOT an accurate repesentation of the amount of stretch. David L; /html/spridgets/2007-08/msg00068.html (7,819 bytes)
3. Re: [Spridgets] Thread Locker on Head Studs (score: 1): Author: rrengineer@dslextreme.com; Date: Wed, 8 Aug 2007 11:17:11 -0700 (PDT); I think you misunderstand. I am talking about the threads into the block, not the nut that holds the head down. Mike David Lieb _______________________________________________ Edit your replies http; /html/spridgets/2007-08/msg00069.html (8,433 bytes)
4. Re: [Spridgets] Thread Locker on Head Studs (score: 1): Author: "David Lieb" <dbl@chicagolandmgclub.com>; Date: Wed, 8 Aug 2007 13:22:51 -0500; Darnit, you are right, Mike. I musta bin votin too much ;-) I could see the use of a threadlocker at the block end of the stud, but I would want to be very selective and avoid the "permanent" ones.; /html/spridgets/2007-08/msg00071.html (7,614 bytes)
5. Re: [Spridgets] Thread Locker on Head Studs (score: 1): Author: "Hal Faulkner" <hal@katemuir.com>; Date: Wed, 8 Aug 2007 13:08:21 -0700; I suggest that youse guys look at the APT web site and read the instructions they have for using or not using thread locker on their studs: Use it or not, but if you do use it make sure that you have; /html/spridgets/2007-08/msg00076.html (7,989 bytes)
6. Re: [Spridgets] Thread Locker on Head Studs (score: 1): Author: "63AHBJ7" <63ahbj7@gmail.com>; Date: Wed, 8 Aug 2007 15:10:44 -0500; Almost all of your post is right on, Hal!! <<APT and my machinist both say the studs should go into the block only a little more than hand tight.>> On the couple hundred motors I have done, I only us; /html/spridgets/2007-08/msg00078.html (7,528 bytes)

Current List: 1 - 6
Page: [1]