- 1. [TR] Fuel Pump Blanking Plate (score: 1)
- Author: "Bob Danielson" <75TR6@tr6.danielsonfamily.org>
- Date: Tue, 6 Jun 2006 19:00:39 -0400
- Does anyone know a source for a fuel pump blanking plate to cover the hole when I remove the mechanical pump? Thanks Bob Danielson 1975 TR6 http://tr6.danielsonfamily.org == This list supported in pa
- /html/triumphs/2006-06/msg00178.html (7,667 bytes)
- 2. Re: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: Bob Labuz <yellowtr@adelphia.net>
- Date: Tue, 6 Jun 2006 18:51:26 -0400
- Bob, I know I sent you a response to this question but I will repeat for the list. Frank Fisher in Vernon Ca has made about a dozen or so. He put a few up on ebay but may have some left. You can cont
- /html/triumphs/2006-06/msg00179.html (7,960 bytes)
- 3. Re: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: Hugh Barber <tr6nut@sbcglobal.net>
- Date: Tue, 06 Jun 2006 22:12:07 -0400
- Bob, I believe that a fuel pump blanking plate for a big-block Chevy works for our TRs. Hugh Barber Stafford, VA '73 TR6 == This list supported in part by The Vintage Triumph Register == http://www.v
- /html/triumphs/2006-06/msg00199.html (7,565 bytes)
- 4. RE: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: "Paul" <rx74evr@mchsi.com>
- Date: Wed, 7 Jun 2006 08:21:19 -0500
- Yes, a big block chevy plate will bolt onto the TR6 block very nicely as that's what I used on my 75 TR6 when I fitted triple Weber carbs a few years back. Paul Bob, I believe that a fuel pump blank
- /html/triumphs/2006-06/msg00216.html (7,731 bytes)
- 5. [TR] Fuel Pump Blanking Plate (score: 1)
- Author: FGFO1@aol.com
- Date: Wed, 7 Jun 2006 18:47:13 EDT
- Well, what started as a friendly help to a fellow lister has generated some interest. So ill throw out advertising for myself as there seems to be some interest. I have fuel blank off plates for the
- /html/triumphs/2006-06/msg00248.html (7,847 bytes)
- 6. Re: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: Dave1massey@cs.com
- Date: Sun, 11 Jun 2006 15:22:30 EDT
- Oh, sorry. I'll bet it's the same as what fits a TR6 (ie: Chevy) Dave == This list supported in part by The Vintage Triumph Register == http://www.vtr.org
- /html/triumphs/2006-06/msg00309.html (7,660 bytes)
- 7. [TR] Fuel Pump Blanking Plate (score: 1)
- Author: FGFO1@aol.com
- Date: Sun, 11 Jun 2006 15:11:58 EDT
- just to confirm earlier reports. wet liner 4 cylinder blanking plates are available now. for those who asked for one ill be mailing them this week, just as soon as i can get to the post office. TR6 b
- /html/triumphs/2006-06/msg00310.html (7,451 bytes)
- 8. RE: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: "Randall" <tr3driver@comcast.net>
- Date: Sat, 10 Jun 2006 17:28:01 -0700
- Dave Massey replied : Er, I was talking about the fuel-injected TR7s and what the factory used to blank the mechanical pump hole that I assume is there. Randall == This list supported in part by The
- /html/triumphs/2006-06/msg00322.html (8,022 bytes)
- 9. Re: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: Dave1massey@cs.com
- Date: Sat, 10 Jun 2006 20:00:43 EDT
- I made my own. But I had access to a fab shop at the time. Dave == This list supported in part by The Vintage Triumph Register == http://www.vtr.org
- /html/triumphs/2006-06/msg00325.html (7,727 bytes)
- 10. [TR] Fuel Pump Blanking Plate (score: 1)
- Author: "Glenn Owen" <mgowen55@hotmail.com>
- Date: Sun, 9 Sep 2007 16:27:22 -0400
- I am installing an electric fuel pump and looking for a blanking plate for the TRactor engine (TR4A). Anybody know where one can be had? Thanks Glenn _______________________________________________ T
- /html/triumphs/2007-09/msg00207.html (7,046 bytes)
- 11. Re: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: "THOMAS FANSHER" <tfansher@comcast.net>
- Date: Sun, 9 Sep 2007 18:23:49 -0400
- Here's the email that I got from Frank when I ordered my blanking plates last year. Hope he still has some. Tom -- Original Message -- From: "Glenn Owen" <mgowen55@hotmail.com> To: <triumphs@autox.te
- /html/triumphs/2007-09/msg00212.html (8,022 bytes)
- 12. Re: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: "Bob Danielson" <75TR6@tr6.danielsonfamily.org>
- Date: Sun, 9 Sep 2007 18:37:18 -0400
- --==1469508465== Content-Type: text/plain; charset="windows-1250" Content-Transfer-Encoding: 7bit Frank Fisher makes them. You can email him at FGFO1@aol.com Bob Danielson 1975 TR6 CF38503U Running w
- /html/triumphs/2007-09/msg00214.html (8,314 bytes)
- 13. Re: [TR] Fuel Pump Blanking Plate (score: 1)
- Author: "THOMAS FANSHER" <tfansher@comcast.net>
- Date: Sun, 9 Sep 2007 18:43:14 -0400
- what i meant to send i guess you'll need my address also 45335 paseo durango temecula ca 92592 Frank Fisher thanks Tom -- Original Message -- From: "Glenn Owen" <mgowen55@hotmail.com> To: <triumphs@a
- /html/triumphs/2007-09/msg00215.html (8,190 bytes)
This search system is powered by
Namazu