Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[oletrucks\]\s+Dual\s+Carbs\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[oletrucks\]\s+Dual\s+Carbs\s*$/: 7 ]

Total 7 documents matching your query.

1. [oletrucks] Dual Carbs (score: 1): Author: Dave Gunn <drgunn@excite.com>; Date: Thu, 26 Apr 2001 11:21:44 -0700 (PDT); I have a dual carb setup on my 235 (with manual choke). Problem is I only have one choke cable. Is there a setup to operate dual chokes from one cable? They are not inline they are parallel. dave ___; /html/oletrucks/2001-04/msg00694.html (6,802 bytes)
2. Re: [oletrucks] Dual Carbs (score: 1): Author: "joe" <chevy1@jps.net>; Date: Thu, 26 Apr 2001 13:29:16 -0700; I had a dual carb set-up in the early 80's and only one carburetor had a choke and it warmed up great! If two chokes are hooked up, you may end up being way to rich on initial start up depending on h; /html/oletrucks/2001-04/msg00695.html (7,614 bytes)
3. Re: [oletrucks] Dual Carbs (score: 1): Author: "Allen Jones" <jonesal@u.washington.edu>; Date: Thu, 26 Apr 2001 15:55:35 -0700; My dual carb setup (parallel too) ran horrible on one choke (even with a heat plate). So I bought a second choke cable, snipped the knob end off, fabbed a small clamp setup from a spare carb (it even; /html/oletrucks/2001-04/msg00698.html (8,702 bytes)
4. [oletrucks] Dual Carbs (score: 1): Author: Grant Galbraith <trks@javanet.com>; Date: Sun, 17 Oct 1999 22:33:40 -0400; I'm working on a offy manifold with dual carbs and Corvette dual exhaust to go with my new dual horns. This is a 235 engine. The directions with the manifold say to take the second choke butterfly ou; /html/oletrucks/1999-10/msg00311.html (7,044 bytes)
5. Re: [oletrucks] Dual Carbs (score: 1): Author: safesix@worldnet.att.net; Date: Mon, 18 Oct 1999 13:23:19 +0000; Assuming the intake is heated from the exhaust riser, the mixture should homogenize well enough in the manifold for fairly equal distribution. I used only the center choke on my 3X1 setup with no pr; /html/oletrucks/1999-10/msg00318.html (7,536 bytes)
6. Re: [oletrucks] Dual Carbs (score: 1): Author: "Al Jones" <jonesal@u.washington.edu>; Date: Mon, 18 Oct 1999 08:14:01 -0700; I tried the dual setup with only one choke. It was horrible when warming up. It's easy to plumb in the second choke. Find a third choke cable clamp off of another carb and fabricate it to fit off the; /html/oletrucks/1999-10/msg00320.html (7,779 bytes)
7. Re: [oletrucks] Dual Carbs (score: 1): Author: L1Chevy@aol.com; Date: Fri, 22 Oct 1999 08:27:48 EDT; Grant, I did this same thing, using Rochesters...I left the choke attached on the rear carb and removed the flap on the front carb..I have had no problems during warm up periods...seems to work fine.; /html/oletrucks/1999-10/msg00452.html (6,810 bytes)

Current List: 1 - 7
Page: [1]