Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[oletrucks\]\s+Howdyaget\s+an\s+\"Easy\s+Out\"\s+Out\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[oletrucks\]\s+Howdyaget\s+an\s+\"Easy\s+Out\"\s+Out\?\s*$/: 13 ]

Total 13 documents matching your query.

1. [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: Hudson29@aol.com; Date: Fri, 26 Nov 1999 18:10:56 EST; I'm back to work today on the same broken bolt that stymied me several weeks ago. The first part of the job was to use a Dremel Moto Tool to grind the shaft of the broken bolt level inside the hole.; /html/oletrucks/1999-11/msg00700.html (9,258 bytes)
2. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: Passnb4U@aol.com; Date: Fri, 26 Nov 1999 18:33:36 EST; grind but star but the I'm Paul: I think you just asked the question that has plagued mankind since the invention of the Easy-Out. I've done it a couple of ways... 1. Use a good punch (read real forg; /html/oletrucks/1999-11/msg00701.html (10,537 bytes)
3. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: Grant Galbraith <trks@javanet.com>; Date: Fri, 26 Nov 1999 18:52:53 -0500; Sounds like someone left you a broken easy out. If it isn't a blind hole and you can drill from the top or other side as far as you can and knock the easy-out out with a punch you could indeed consid; /html/oletrucks/1999-11/msg00702.html (10,872 bytes)
4. RE: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: "Kevin D. Pennell" <oletwuk@amaze.net>; Date: Fri, 26 Nov 1999 19:14:22 -0500; If it is an "Easy Out", the material is so hard that you can readily "shatter it". Use a center punch or a small punch and a hammer and break it apart one smack at a time. Aim true, as your block do; /html/oletrucks/1999-11/msg00703.html (10,770 bytes)
5. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: "Murray Whitlock" <mp.w@sk.sympatico.ca>; Date: Fri, 26 Nov 1999 19:24:53 -0600; Paul: If you have access to a welder, here is what i have used here on the farm to get brocken bolts out. I take a washer with the same size hole as the bolt, place it over the brocken off end of the; /html/oletrucks/1999-11/msg00705.html (10,984 bytes)
6. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: CLLLSLS@aol.com; Date: Fri, 26 Nov 1999 21:54:10 EST; Definatley don't use a carbide drill bit. It is the only thing that will drill through it, but if you try to use a carbide drill in a hand drill you will probably snap it off. The best thing to do wo; /html/oletrucks/1999-11/msg00708.html (9,775 bytes)
7. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: "Don Slaney" <ppm@dlcwest.com>; Date: Fri, 26 Nov 1999 21:08:33 -0600; After all I see here, my easy outs are on the way out!!!! There must be easier "out" ways. Regards to all, Don. Then almost several grind but star what but oletrucks is devoted to Chevy and GM trucks; /html/oletrucks/1999-11/msg00709.html (11,938 bytes)
8. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: "Claude Ramey" <cramey@n-link.com>; Date: Fri, 26 Nov 1999 21:45:32 -0600; I broke an easy out in a bolt in my boat motor. Impossible to drill. I took a very small (very small) bit and drilled alot of holes around it (kinda like cutting it out) until i could get it out. The; /html/oletrucks/1999-11/msg00710.html (13,281 bytes)
9. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: Grant Galbraith <trks@javanet.com>; Date: Fri, 26 Nov 1999 23:21:50 -0500; I drill many a broken bolt out where I work. I seldom (never) use easy out's and EDM is not an option on an entire jet engine. We usually drill it out to size or nearly size, pick out remnants and re; /html/oletrucks/1999-11/msg00711.html (8,911 bytes)
10. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: Advdesign1@aol.com; Date: Sat, 27 Nov 1999 07:56:07 EST; << I'm back to work today on the same broken bolt that stymied me several weeks ago.... it looks like a metallic five pointed star is imbedded in the broken bolt. It is very tough, and even the new C; /html/oletrucks/1999-11/msg00717.html (8,747 bytes)
11. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: Wayne Osborne <wcosborne@inetnow.net>; Date: Sat, 27 Nov 1999 10:46:48 -0500; I have used the tap extractors mentioned below but I must say if the tap is wedged in there or stuck these extractors did not help my situation. The fingers are extended out of cylinder and slid down; /html/oletrucks/1999-11/msg00723.html (9,643 bytes)
12. Re: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: Grant Galbraith <trks@javanet.com>; Date: Sat, 27 Nov 1999 10:50:22 -0500; Hello Bob, I don't know what your luck has been with tap extractors but I have never had them work on small size taps such as 1/4 or 5/16. I don't think they would grip a broken a broken easy out. Gr; /html/oletrucks/1999-11/msg00724.html (9,087 bytes)
13. RE: [oletrucks] Howdyaget an "Easy Out" Out? (score: 1): Author: "Tom Burt" <tburt@hirose.com>; Date: Mon, 29 Nov 1999 09:27:45 -0800; Ditto on the "breakout" method. I've tried the same with extremely poor results. The only option is to drill out using a carbide drill. Try to start with the smallest yet sturdiest bit to maintain a; /html/oletrucks/1999-11/msg00771.html (9,791 bytes)

Current List: 1 - 13
Page: [1]