- 1. [oletrucks] Replacement rear end questions (score: 1)
- Author: Ryan Sain <rsain@gte.net>
- Date: Tue, 04 Feb 2003 13:17:06 -0800
- Hi all, 59 chevy apache. Doing a rear end swap and have been suggested to pick up a late 60's or early 70's Nova/Camaro rear end. Great idea, but these things are nearly impossible to find up here (S
- /html/oletrucks/2003-02/msg00056.html (7,898 bytes)
- 2. Re: [oletrucks] Replacement rear end questions (score: 1)
- Author: Jeffros54@cs.com
- Date: Tue, 4 Feb 2003 17:36:43 EST
- I was told the same on the rears, But, The S-10 is a lot narrower. I can measure one tomorrow and let you know for sure. The housing is the same as the Camaro, but I think it will be too narrow for a
- /html/oletrucks/2003-02/msg00058.html (7,578 bytes)
- 3. Re: [oletrucks] Replacement rear end questions (score: 1)
- Author: Ryan Sain <rsain@gte.net>
- Date: Tue, 04 Feb 2003 14:52:15 -0800
- Ha! No tubbing..... I don9t think the better half would approve. I would greatly appreciate a measurement on an s-10, as I don9t have one around here to measure. - Ryan the oletrucks is devoted to Ch
- /html/oletrucks/2003-02/msg00059.html (7,911 bytes)
- 4. Re: [oletrucks] Replacement rear end questions (score: 1)
- Author: "Vonne Volwerk" <chevy@zeelandnet.nl>
- Date: Wed, 5 Feb 2003 01:05:30 +0100 (West-Europa (standaardtijd))
- Hi Ryan, In the summer of 2002 I replaced the original rearend in my 1958 with a rearend out of a 1980 Chevrolet Blazer, the rear axle is allmost the same width from baking plate to backing plate. I
- /html/oletrucks/2003-02/msg00060.html (9,058 bytes)
- 5. Re: [oletrucks] Replacement rear end questions (score: 1)
- Author: Jeffros54@cs.com
- Date: Wed, 5 Feb 2003 20:31:18 EST
- I finally got out and measured the S-10 rear end. (1988). Backing plate to backing plate is 47 3/4" Drum face to Drum face is 54 1/4" Hope this helps Later Jeff oletrucks is devoted to Chevy and GM t
- /html/oletrucks/2003-02/msg00087.html (7,566 bytes)
- 6. Re: [oletrucks] Replacement rear end questions (score: 1)
- Author: "Steve Hanberg" <Steve@OldSub.com>
- Date: Wed, 5 Feb 2003 18:44:32 -0800
- The rear I put under my 55 1st was more like 61 or 62 flange to flange. oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
- /html/oletrucks/2003-02/msg00092.html (8,052 bytes)
- 7. Re: [oletrucks] Replacement rear end questions (score: 1)
- Author: Ryan Sain <rsain@gte.net>
- Date: Thu, 06 Feb 2003 08:30:45 -0800
- I'm just over 50" from backing plate to backing plate now, so I don't think that the the s-10 will work. Thank you for checking up on it though.... - Ryan oletrucks is devoted to Chevy and GM trucks
- /html/oletrucks/2003-02/msg00098.html (7,868 bytes)
- 8. RE: [oletrucks] Replacement rear end questions (score: 1)
- Author: "Leslie Kester" <dlkester@cox-internet.com>
- Date: Fri, 7 Feb 2003 14:49:39 -0600
- is anyone going to Tulsa for the car show from northwest Ar. we will meet at 8:00 at outlet mall in Springdale Ar if anyone wants to go Ha! No tubbing..... I don9t think the better half would approve
- /html/oletrucks/2003-02/msg00131.html (8,558 bytes)
This search system is powered by
Namazu