Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Ball\s+Joint\s+Blues\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Ball\s+Joint\s+Blues\s*$/: 8 ]

Total 8 documents matching your query.

1. Ball Joint Blues (score: 1): Author: DBHMGB@aol.com; Date: Sat, 9 Aug 1997 18:46:07 -0400 (EDT); Greetings to all! It's been quite a while since I've been on the list. Hello to all who don't know me, and to those who do know me, all I can say is I'll be careful! (I was also dhughes@troweprice.co; /html/mgs/1997-08/msg00488.html (7,432 bytes)
2. Re: Ball Joint Blues (score: 1): Author: "William C. Mills" <williem@mindspring.com>; Date: Sat, 09 Aug 1997 20:19:24 -0400; my remedy was to unscrew the nut on the ball joint to the end of the threads, place a floor jack under the joint and jack up to put pressure on the bottom of the joint. this will probably not get the; /html/mgs/1997-08/msg00490.html (8,417 bytes)
3. Re: Ball Joint Blues (score: 1): Author: DBHMGB@aol.com; Date: Sat, 9 Aug 1997 20:41:29 -0400 (EDT); Thanks, I'll give this a try! places i.e. the I'm afraid I'm gonna be in the same situation... What did you do at this point? [207.69.; /html/mgs/1997-08/msg00492.html (9,233 bytes)
4. Re: Ball Joint Blues (score: 1): Author: "William C. Mills" <williem@mindspring.com>; Date: Sat, 09 Aug 1997 23:17:49 -0400; After a lot of liquid wrench and pipe wrench twisting, I got out the blue wrench. That took are of it. Bill Mills 74 BGT; /html/mgs/1997-08/msg00498.html (7,346 bytes)
5. Re: Ball Joint Blues (score: 1): Author: Arthur Pfenninger <ch155@FreeNet.Buffalo.EDU>; Date: Sun, 10 Aug 1997 09:58:58 -0400 (EDT); If the tie rod end won't come off soak it with PB Blaster available at NAPA or other parts stores. Forget WD40 it is good for squeeks but not on rust. If the soaking doesn't work heat the rod end wit; /html/mgs/1997-08/msg00510.html (10,115 bytes)
6. Re: Ball Joint Blues (score: 1): Author: britcars@juno.com (Lawrence J Alexander); Date: Mon, 11 Aug 1997 12:00:49 EDT; (SNIP) get the ball joints loose. Any tips without destroying the joint? Actually, there's no need to separate the ball joints (tie rod ends) from the steering arms. If you simply undo the lock nut,; /html/mgs/1997-08/msg00562.html (7,517 bytes)
7. RE: Ball Joint Blues (score: 1): Author: "doug russell" <dr-doug@msn.com>; Date: Mon, 11 Aug 97 20:11:37 UT; Good tricks to note the position of the nut (so as to not upset the alignment) includes white out or tape or both. You should make sure that it is well marked as alignment can be a pain in the butt a; /html/mgs/1997-08/msg00574.html (8,022 bytes)
8. Re: Ball Joint Blues (score: 1): Author: britcars@juno.com (Lawrence J Alexander); Date: Mon, 11 Aug 1997 16:40:12 EDT; Dan.... The book says: "Prise up the indentations in the locking rings clear of the slots in the rack and ball housing. Slacken back the locking ring and unscrew the housing to release the tie ord, b; /html/mgs/1997-08/msg00575.html (8,905 bytes)

Current List: 1 - 8
Page: [1]