Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Clutch\s+Bleeding\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Clutch\s+Bleeding\s*$/: 12 ]

Total 12 documents matching your query.

1. Clutch Bleeding (score: 1): Author: Mark Wright <mewright@eznet.net>; Date: Mon, 19 Aug 2002 03:56:19 GMT; I've been sitting on the sidelines for a few months since a bought my 6, but enough is enough! When I bought the car the clutch pedal went to the floor so I rebuilt the clutch MC and SC. Now I'm havi; /html/6pack/2002-08/msg00297.html (7,988 bytes)
2. Re: Clutch Bleeding (score: 1): Author: william mcintire <william.mcintire@wright.edu>; Date: Mon, 19 Aug 2002 09:15:39 -0400; Clutches do stick to flywheels. With the engine off, put the car in 4th gear, stand on the brakes, push the clutch down and try to start it. Just bump the starter, don't let engage for a long time p; /html/6pack/2002-08/msg00302.html (7,469 bytes)
3. Fwd: Clutch Bleeding (score: 1): Author: Timothy Holbrook <tjh173@yahoo.com>; Date: Mon, 19 Aug 2002 09:57:26 -0700 (PDT); Well, if you are getting 1/2" of travel on the slave cylinder pushrod (I assume that's what you meant in your email), then it sounds like your hydraulics are working fine. When you push on the clutch; /html/6pack/2002-08/msg00308.html (10,013 bytes)
4. Re: Clutch Bleeding (score: 1): Author: "Michael Lupynec" <mlupynec@globalserve.net>; Date: Mon, 19 Aug 2002 13:27:20 -0400; Start engine in neutral, get the car rolling down an incline or get a hand push to a few miles per hour, slip it into first gear and continue motoring slowly, push clutch pedal all the way down and a; /html/6pack/2002-08/msg00309.html (9,510 bytes)
5. RE: Clutch Bleeding (score: 1): Author: "R. Ashford Little II" <ralittle2@mindspring.com>; Date: Mon, 19 Aug 2002 14:45:45 -0400; Thanks Tim, that is a great test for all of to remember. R. Ashford Little II www.geocities.com/ralittle2 Well, if you are getting 1/2" of travel on the slave cylinder pushrod (I assume that's what y; /html/6pack/2002-08/msg00310.html (10,535 bytes)
6. RE: Clutch Bleeding (score: 1): Author: "Bert Van der Stee" <bert.van.der.stee@pandora.be>; Date: Mon, 19 Aug 2002 23:01:11 +0200; about your last sentence - "am using the middle hole". Is it also OK to use one of the other three holes ? I thought I read somewhere in the manual to use only the middle one, but I could be wrong ?; /html/6pack/2002-08/msg00312.html (9,920 bytes)
7. RE: Clutch Bleeding (score: 1): Author: Mark Wright <mewright@eznet.net>; Date: Wed, 21 Aug 2002 05:00:46 GMT; Well I tried many of the suggestions offered from those who gratefully responded, but to no avail. I tried many of the ideas to free up a frozen flywheel and clutch, including - starting in gear, lif; /html/6pack/2002-08/msg00347.html (7,896 bytes)
8. RE: Clutch Bleeding (score: 1): Author: Timothy Holbrook <tjh173@yahoo.com>; Date: Wed, 21 Aug 2002 13:51:05 -0700 (PDT); Sorry, I didn't mean to suggest that the arm will not move at all. You should be able to move the arm towards the back of the car until the bearing comes in contact with the clutch. You should then b; /html/6pack/2002-08/msg00365.html (9,323 bytes)
9. RE: Clutch Bleeding (score: 1): Author: Andrew Packard <apackard@triad.rr.com>; Date: Wed, 21 Aug 2002 23:08:17 -0400; In my recent TR250 tranny rebuild, my mechanic welded the fork to the shaft in addition to replacing the pin since that area is notorious for problems. I pulled the tranny three times to get it rebui; /html/6pack/2002-08/msg00377.html (8,617 bytes)
10. Re: Clutch Bleeding (score: 1): Author: "Michael Lupynec" <mlupynec@globalserve.net>; Date: Wed, 21 Aug 2002 23:36:35 -0400; I slipped a memory chip on my holes - I am on the top hole. It is written to use the middle hole, (the factory setting). The top hole gives you more clutch plate travel, but requires more hydraulic p; /html/6pack/2002-08/msg00379.html (11,589 bytes)
11. Clutch Bleeding (score: 1): Author: Kendall Larsen <mailkendall@sbcglobal.net>; Date: Mon, 31 Jul 2006 12:20:58 -0700 (PDT); Hi List, I'm having some problems with my clutch. And I want to check "air in the system" off of the list of likely culprits. Is bench bleeding the most reliable way of ensuring that there is no air; /html/6pack/2006-07/msg00382.html (6,539 bytes)
12. Re: Clutch Bleeding (score: 1): Author: tr6taylor@webtv.net (Sally or Dick Taylor); Date: Mon, 31 Jul 2006 14:37:54 -0700; Kendall--One sure-fire way to bleed the clutch MC is to connect a clear tube from the (slightly opened) Slave bleed screw, back up into the MC reservoir. If there's any air in the line, you'll see th; /html/6pack/2006-07/msg00384.html (7,624 bytes)

Current List: 1 - 12
Page: [1]