Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Copper\s+gasket\s+on\s+a\s+recessed\s+block\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Copper\s+gasket\s+on\s+a\s+recessed\s+block\?\s*$/: 7 ]

Total 7 documents matching your query.

1. Copper gasket on a recessed block? (score: 1): Author: Gt6steve@aol.com; Date: Mon, 5 May 2003 12:26:32 EDT; Good morning Amici, I'm soliciting opinions on using a copper head gasket on the recessed block of the GT6. I don't want to shave the block to get the smooth deck so I'm pondering the effects on the; /html/fot/2003-05/msg00032.html (7,579 bytes)
2. Re: Copper gasket on a recessed block? (score: 1): Author: Joe Curry <Spitlist@gte.net>; Date: Mon, 05 May 2003 10:18:49 -0700; It probably won't seal well since there will not be any protrusion on the gasket to fit into the depression. If you can't get rid of the depression, it's probably better to use a composition gasket; /html/fot/2003-05/msg00034.html (8,111 bytes)
3. Re: Copper gasket on a recessed block? (score: 1): Author: "A.J. & C. Wood" <wood@dandrade.freeserve.co.uk>; Date: Mon, 5 May 2003 21:01:01 +0100; Why not just use an original Payen head gasket? - OK up to +.040". At +0.060" the inner fire ring can touch the piston crown. To improve sealing, polish off the lacquer with superfine Scotchbrite, th; /html/fot/2003-05/msg00035.html (8,412 bytes)
4. Re: Copper gasket on a recessed block? (score: 1): Author: "John Kipping" <johnkipping@inet.net.nz>; Date: Tue, 6 May 2003 09:44:31 +1200; If fitting +60 pistons to a recessed block then it is best to chamfer the tops of the pistons to stop them hitting the head gasket - been there - done that, makes a noise. John Kipping -- Original Me; /html/fot/2003-05/msg00036.html (9,220 bytes)
5. Re: Copper gasket on a recessed block? (score: 1): Author: "John Kipping" <johnkipping@inet.net.nz>; Date: Tue, 6 May 2003 09:37:26 +1200; I can guarantee it won't work, if the car will even start the gasket won't last long. John Kipping -- Original Message -- From: "Joe Curry" <Spitlist@gte.net> To: <Gt6steve@aol.com> Cc: <FOT@autox.te; /html/fot/2003-05/msg00037.html (8,805 bytes)
6. RE: Copper gasket on a recessed block? (score: 1): Author: Bill Babcock <BillB@bnj.com>; Date: Mon, 5 May 2003 14:51:03 -0700; You can get copper or steel rings cut at a metal slitting company--they use a variety of technologies to cut patterns. No idea of the cost. You could also try a fly cutter, I've used them to make alu; /html/fot/2003-05/msg00038.html (8,410 bytes)
7. Re: Copper gasket on a recessed block? (score: 1): Author: Gt6steve@aol.com; Date: Mon, 5 May 2003 19:54:59 EDT; That's the kid of thinking I was pursuing! Instead of the brazing I'd just set the rings in the grooves with a .003-.005 deck height and them torque it down. Basically an O-ringed head with wider O-r; /html/fot/2003-05/msg00039.html (8,132 bytes)

Current List: 1 - 7
Page: [1]