Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Cylinder\s+Head\s+Studs\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Cylinder\s+Head\s+Studs\s*$/: 7 ]

Total 7 documents matching your query.

1. Cylinder Head Studs (score: 1): Author: "Randy Trautman" <trautman@nwlink.com>; Date: Tue, 1 Jul 2003 17:22:37 -0700; What is the correct method to install and torque new cylinder head studs on a 5 main MGB? Thanks, Randy Portland, OR 69 MGB/GT 72 MGB 66 MGB (engine goes in next week!) /// or try http://www.team.net; /html/mgs/2003-07/msg00039.html (6,603 bytes)
2. Re: Cylinder Head Studs (score: 1): Author: "Telewest $PH$" <paul.hunt1@blueyonder.co.uk>; Date: Thu, 3 Jul 2003 11:31:02 +0100; Never torque studs into the block. Make sure the threads are clean then just bottom them, using two nuts if necessary. Torqueing the studs in to the block can crack it. Torqueing the head nuts on is; /html/mgs/2003-07/msg00088.html (7,145 bytes)
3. Re: cylinder head studs (score: 1): Author: David Woerpel <dwoerpel@wi.net>; Date: Sat, 01 Sep 2001 23:14:22 -0500; Amen to that! Dave (older and definitely wiser) 59 MGA 1500 59 :{) /// /// mgs@autox.team.net mailing list /// (If they are dupes, this trailer may also catch them.); /html/mgs/2001-09/msg00024.html (6,656 bytes)
4. cylinder head studs (score: 1): Author: "Gordon Blake" <blake352@home.com>; Date: Thu, 30 Aug 2001 21:12:17 -0500; What is the proper technique for removing and fitting new studs on the cylinder head that are used to attach the carburetors and exhaust manifold? The old ones are worn out and I already have the new; /html/mgs/2001-08/msg00776.html (6,811 bytes)
5. Re: cylinder head studs (score: 1): Author: Barney Gaylord <barneymg@ntsource.com>; Date: Fri, 31 Aug 2001 00:25:49 -0500; cylinder head that are used to attach the carburetors and exhaust manifold? .... Typical stud removal technique. Install two 5/16-24 hex nuts on the stud, tighten them against each other to jam the t; /html/mgs/2001-08/msg00784.html (7,823 bytes)
6. Re: cylinder head studs (score: 1): Author: "mgamgb" <mgamgb@ihug.co.nz>; Date: Fri, 31 Aug 2001 17:44:34 +1200; Further to Barneys note - The studs thenselves should not be overtightened into the block, if the threads on both the stud and the block are all clean and undamaged the studs should go in finger tigh; /html/mgs/2001-08/msg00785.html (7,236 bytes)
7. RE: cylinder head studs (score: 1): Author: "Unger, Larry G" <larry.g.unger@lmco.com>; Date: Fri, 31 Aug 2001 01:53:33 -0400; WOW ... I never realized this ... Barney, thanks again for the excellent tid bits of info! Larry Unger '61 MGA 1600 MkII /// /// mgs@autox.team.net mailing list /// (If they are dupes, this trailer; /html/mgs/2001-08/msg00786.html (7,077 bytes)

Current List: 1 - 7
Page: [1]