Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Damper\s+Blades\-What\s+For\s+And\s+How\s+Do\s+You\s+$Ah$\s+Test\s+Them\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Damper\s+Blades\-What\s+For\s+And\s+How\s+Do\s+You\s+$Ah$\s+Test\s+Them\?\s*$/: 6 ]

Total 6 documents matching your query.

1. Damper Blades-What For And How Do You (Ah) Test Them? (score: 1): Author: ebrown@ms.com; Date: Thu, 9 Oct 1997 07:57:30 -0400; My tenure as a Morgan owner is short (two years) but event-filled. The one device on the car that I've never seen before on other cars, in one form or another, are these damper blades in the front su; /html/morgans/1997-10/msg00028.html (8,388 bytes)
2. Re: Damper Blades-What For And How Do You (Ah) Test Them? (score: 1): Author: "Warden, Tom" <twarden@usia.gov>; Date: Thu, 9 Oct 1997 10:05:08 -0400; It is actually the damper blade shims that may need attention. The first thing to do is grab hold of the damper blade and give it a good shake. If there is any play the shims need to be adjusted. The; /html/morgans/1997-10/msg00029.html (7,779 bytes)
3. Re: Damper Blades-What For And How Do You (Ah) Test Them? (score: 1): Author: Joseph DeLuca <DELUCAJ@mops.wl.com>; Date: Thu, 09 Oct 1997 10:59:08 -0400; I agree with Tom's recommendation (below) about the damper blades, and his method of adjustment. You should also check the 1/2' diameter rod next to the blade. If the bolt that anchors the rod to the; /html/morgans/1997-10/msg00030.html (8,609 bytes)
4. Re: Damper Blades-What For And How Do You (Ah) Test Them? (score: 1): Author: "Noah L. Anglin" <nlaark@hooked.net>; Date: Thu, 09 Oct 1997 09:42:58 -0700; I have owned two Morgans over the past years and a partial solution of the "shimmy" on both was the same. Have the wire wheels tuned (that is, if you have wires). This made more and better differenc; /html/morgans/1997-10/msg00031.html (7,588 bytes)
5. RE: Damper Blades-What For And How Do You (Ah) Test Them? (score: 1): Author: "Vodden, Dave" <Dave.Vodden@Telematics.com>; Date: Thu, 09 Oct 97 14:21:00 PDT; The shimmy problem is caused by the large positive offset of the contact patch relative to the kingpin centre which results in a particular sensitivity to disturbing forces such as balance or brake b; /html/morgans/1997-10/msg00035.html (10,371 bytes)
6. Re: Damper Blades-What For And How Do You (Ah) Test Them? (score: 1): Author: TrmpetDave@aol.com; Date: Sat, 11 Oct 1997 23:23:37 -0400 (EDT); Test the damper blade adjustment first-there should be no fore-and aft motion possible where they go through the clanmp on the chassis. If they are loose, adjust the litle weges by loosening the two; /html/morgans/1997-10/msg00046.html (7,739 bytes)

Current List: 1 - 6
Page: [1]