- 1. Drive (Propeller) Shaft (score: 1)
- Author: "Jim Johnson" <bmwwxman@gmail.com>
- Date: Fri, 21 Apr 2006 18:58:35 -0500
- I've tracked my rear end "clunk" down to U joints as originally suspected. I just read through my Haynes for the procedure to replace them. Disassembly looks easy and straight forward but when it co
- /html/spridgets/2006-04/msg00964.html (7,834 bytes)
- 2. Re: Drive (Propeller) Shaft (score: 1)
- Author: Jay Fishbein <type79@ix.netcom.com>
- Date: Fri, 21 Apr 2006 20:14:27 -0400
- If your arm is slim enough, you can reach in there. jay fishbein wallingford, ct <http://home.ix.netcom.com/%7Etype79/> http://home.ix.netcom.com/~type79/ <http://home.ix.netcom.com/%7Etype79/> "My G
- /html/spridgets/2006-04/msg00965.html (7,386 bytes)
- 3. Re: Drive (Propeller) Shaft (score: 1)
- Author: Frank Clarici <spritenut@comcast.net>
- Date: Fri, 21 Apr 2006 20:45:16 -0400
- Getting the old U joints out is the hard part. Putting in new ones is a whole lot easier. 2 ways to reinstall the d/shaft to the trans. 1) have a helper with a long screwdriver or suitable rod guide
- /html/spridgets/2006-04/msg00968.html (7,430 bytes)
- 4. Re: Drive (Propeller) Shaft (score: 1)
- Author: Bill L <pythias@pacifier.com>
- Date: Fri, 21 Apr 2006 18:11:29 -0700
- Hello Jim, the "book" says its a two person operation.. one guy lifts the shaft with an 8" screwdriver through the hole in the tunnel where you lube the U-joints, while the other pushes the shaft int
- /html/spridgets/2006-04/msg00969.html (7,319 bytes)
- 5. Re: Drive (Propeller) Shaft (score: 1)
- Author: Jpp963@aol.com
- Date: Fri, 21 Apr 2006 21:19:59 EDT
- spritenut@comcast.net writes: The tape will scare the crap out of you when it starts to flop around in the tunnel but it will come off in a couple miles. Or sometimes it takes like 70 - 80 miles, so
- /html/spridgets/2006-04/msg00970.html (7,112 bytes)
- 6. Re: Drive (Propeller) Shaft (score: 1)
- Author: "Jim Johnson" <bmwwxman@gmail.com>
- Date: Fri, 21 Apr 2006 20:34:55 -0500
- Guy Weller offers: longer than it is. Jay Fishbein sez: Well, HeLL!! Why didn't I think of that!! Hard part will be getting my lard a$$ under there to do the work!! Cheers!! Jim - 68 Midget in Dodge
- /html/spridgets/2006-04/msg00972.html (7,410 bytes)
- 7. Re: Drive (Propeller) Shaft (score: 1)
- Author: "Ed" <justbrits@comcast.net>
- Date: Fri, 21 Apr 2006 22:34:55 -0500
- <<Why didn't I think of that!! >> er??????????? LOL, JIm!!! 'course back to the "lard..........." part Ed PS: Mind you I not you said ANYTHING about your back!!!!!
- /html/spridgets/2006-04/msg00975.html (7,018 bytes)
This search system is powered by
Namazu