Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Driveshaft\s+install\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Driveshaft\s+install\s*$/: 9 ]

Total 9 documents matching your query.

1. Driveshaft Install (score: 1): Author: Jason Urban <jurban@p3.net>; Date: Tue, 08 Jun 1999 11:35:12 -0400; The method I used in the last 2 installs of the driveshaft was this... 1) Have the shift lever cover off so you can see the end of the tranny. 2) Bend a really stiff wire into a loop and insert down; /html/spridgets/1999-06/msg00474.html (7,371 bytes)
2. Driveshaft install (score: 1): Author: Unknown; Date: Thu, 09 Sep 2004 17:17:31 -0500; Tried something today... installing the driveshaft on the tranny before reinstalling the engine/tranny lump. I was trying to avoid the James Herriot assisting-the-calf-birthing scenario I always seem; /html/spridgets/2004-09/msg00160.html (7,624 bytes)
3. Re: Driveshaft install (score: 1): Author: Unknown; Date: Thu, 9 Sep 2004 19:19:55 -0500 reply-type=response; From "Peter C." Peter, that statement baffled me. I (almost) immediately went out to the garage and dug up a driveshaft and transmission to verify this claim. I can now say with certainty that it doe; /html/spridgets/2004-09/msg00161.html (8,389 bytes)
4. Re: Driveshaft install (score: 1): Author: Unknown; Date: Thu, 09 Sep 2004 19:55:38 -0500; If the car is up high enough, one can reach in the tunnel from the back near the diff, and push it into place. Brad Check out the new British Cars Forum: http://www.team.net/the-local/tiki-view_forum; /html/spridgets/2004-09/msg00163.html (8,182 bytes)
5. Re: Driveshaft install (score: 1): Author: Unknown; Date: Thu, 09 Sep 2004 23:03:16 -0400; Or if your car has been DPO'd like mine, just use the handy access hole chopped in the bottom of the tunnel. (Probably ought to fix that someday!) Eddie Check out the new British Cars Forum: http://w; /html/spridgets/2004-09/msg00168.html (8,853 bytes)
6. Re[2]: Driveshaft install (score: 1): Author: Unknown; Date: Thu, 9 Sep 2004 21:08:15 -0700; hmmm. is it really THAT much easier with a 5 speed than a rib case? i just reached down thru the shifter hole and guided the drive shaft home... course there were two of us... one pushing the shaft; /html/spridgets/2004-09/msg00169.html (8,445 bytes)
7. Re: Driveshaft install (score: 1): Author: Unknown; Date: Fri, 10 Sep 2004 00:23:34 EDT; Just be sure that you have plenty of rags around to mop up the spills. Don't plan to try this one again. We had to pull the engine back out and towel the transmission cavity out because we couldn't k; /html/spridgets/2004-09/msg00170.html (8,511 bytes)
8. RE: Driveshaft install (score: 1): Author: Unknown; Date: Fri, 10 Sep 2004 00:40:13 -0700; Another fine use for the Mityvac, just suck a vacuum on the tranny and get the driveshaft close. Crash If the car is up high enough, one can reach in the tunnel from the back near the diff, and push; /html/spridgets/2004-09/msg00172.html (8,265 bytes)
9. Re: Driveshaft install (score: 1): Author: Unknown; Date: Fri, 10 Sep 2004 06:03:31 -0500; Truth be told, there IS a hole cut in the tunnel on the INSIDE if the car, in our 68. I had to fabricate a cover for it, as I was not fond of the idea of losing a U joint that close to my leg with no; /html/spridgets/2004-09/msg00174.html (8,892 bytes)

Current List: 1 - 9
Page: [1]