Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*GT6\s+ring\s+and\s+pinion\s+interchange\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*GT6\s+ring\s+and\s+pinion\s+interchange\?\s*$/: 7 ]

Total 7 documents matching your query.

1. Re: GT6 ring and pinion interchange? (score: 1): Author: BillDentin@aol.com; Date: Tue, 17 Dec 2002 11:04:57 EST; Erik: I'm no expert in these matters, but it's my understanding that while it might not be important with 'new parts', once they've been run and mated, they should no longer be switched around. Other; /html/fot/2002-12/msg00181.html (8,034 bytes)
2. GT6 ring and pinion interchange? (score: 1): Author: Erik Quackenbush <erik@midwestfilter.com>; Date: Tue, 17 Dec 2002 09:56:55 -0600; Do Spitfire/GT6 ring and pinions have to remain in matched pairs? Are the 9 teeth on a 4.11 pinion the same as the 9 teeth on a 3.89 pinion? I've got a Spitfire 4.11 (37 tooth ring, 9 tooth pinion) w; /html/fot/2002-12/msg00182.html (7,621 bytes)
3. Re: GT6 ring and pinion interchange? (score: 1): Author: WEmery7451@aol.com; Date: Tue, 17 Dec 2002 12:58:47 EST; << Do Spitfire/GT6 ring and pinions have to remain in matched pairs? >> I have always been told that all ring and pinions are made as matched sets and cannot be interchanged. If you have two identica; /html/fot/2002-12/msg00183.html (7,446 bytes)
4. Re: GT6 ring and pinion interchange? (score: 1): Author: BRITPAC@aol.com; Date: Tue, 17 Dec 2002 13:29:21 EST; I di d a mismatched 4:11 gear set in my Vitesse, and it howled like a son of a gun at different speeds, almost silent at others. Aside from that it seemed to work fine. I eventually put in a matched; /html/fot/2002-12/msg00184.html (7,105 bytes)
5. RE: GT6 ring and pinion interchange? (score: 1): Author: Bill Babcock <BillB@bnj.com>; Date: Tue, 17 Dec 2002 10:22:46 -0800; All good comments and probably mostly true, though I think it's the wear that matters, not the original manufacturing tolerances. But only relevant for thousands of miles of ordinary use or hundreds; /html/fot/2002-12/msg00185.html (8,191 bytes)
6. Re: GT6 ring and pinion interchange? (score: 1): Author: "Tom Strange" <tstrange@new.rr.com>; Date: Tue, 17 Dec 2002 16:29:51 -0600; I just went through this.... I'm not sure, but I think if you compare the two pinions, they will be a little different. It may just be the curvature of the teeth. You may be able to get away with th; /html/fot/2002-12/msg00186.html (8,495 bytes)
7. Re: GT6 ring and pinion interchange? (score: 1): Author: "John Kipping" <johnkipping@inet.net.nz>; Date: Wed, 18 Dec 2002 10:44:20 +1300; You certainly can't mix up different ratios as the size of the teeth are different - mixing up different sets of the same ratio will result in noise and premature wear so in general it is a waste of; /html/fot/2002-12/msg00187.html (8,463 bytes)

Current List: 1 - 7
Page: [1]