Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Gas\s+No\s+gas\s+MIG\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Gas\s+No\s+gas\s+MIG\s*$/: 22 ]

Total 22 documents matching your query.

1. Gas No gas MIG (score: 1): Author: "Robert Dardano" <19to1tr6@attbi.com>; Date: Sat, 8 Mar 2003 19:35:50 -0500; Can anyone sujest the proper fluxcore wire to use for Tr-6 body pannels?My welder will take .023 up to .035 The rolls are not cheap so I would like to start with the right one for the job I have no e; /html/fot/2003-03/msg00118.html (7,478 bytes)
2. RE: Gas No gas MIG (score: 1): Author: Bill Babcock <BillB@bnj.com>; Date: Sun, 9 Mar 2003 07:32:00 -0800; I don't think most welders would recommend fluxcore wire for body panels. It makes a messy weld that's hard to clean up. At least that's my experience, but then I'm a fairly lousy welder that tends t; /html/fot/2003-03/msg00126.html (8,066 bytes)
3. Re: Gas No gas MIG (score: 1): Author: Larry Young <cartravel@pobox.com>; Date: Sun, 09 Mar 2003 10:01:57 -0600; I've heard nothing good about fluxcore wire. You should rig it for gas. I believe I use an argon/co2 mix (ask your local welding supply) and 0.030 wire. The secret to mig welding body panels is to n; /html/fot/2003-03/msg00129.html (8,330 bytes)
4. Re: Gas No gas MIG (score: 1): Author: "Robert Dardano" <19to1tr6@attbi.com>; Date: Sun, 9 Mar 2003 14:05:33 -0500; Thanks to everyone that responed to my question,RE wire selection I should use the colective talent of this list more often Now with that said can anyone use a 10lbs roll of .035 flux core wire thank; /html/fot/2003-03/msg00131.html (8,344 bytes)
5. Re: Gas No gas MIG (score: 1): Author: "elliottd" <elliottd@look.ca>; Date: Mon, 10 Mar 2003 12:26:42 -0500; For all my work, including body panels, I use the Argon - Co2 gas bottle and 0.023" diameter MIG mild steel wire which is copper coated to keep it from getting rusty when I'm not using it. It works g; /html/fot/2003-03/msg00137.html (9,509 bytes)
6. RE: Gas No gas MIG (score: 1): Author: Bill Babcock <BillB@bnj.com>; Date: Mon, 10 Mar 2003 10:33:31 -0800; Sounds like everyone has had the same experience. I think flux core is fine when it's sunday and you're out of gas. It works fine but it's messier. It's also harder to get it to feed cleanly--perhaps; /html/fot/2003-03/msg00138.html (10,399 bytes)
7. Re: Gas No gas MIG (score: 1): Author: "Robert Dardano" <19to1tr6@attbi.com>; Date: Mon, 10 Mar 2003 20:12:13 -0500; Thanks for all the help I have done my bit for the economoney and bought the tank I am gonna learn how to use the welda and build tanks . rob -- Original Message -- From: "Bill Babcock" <BillB@bnj.co; /html/fot/2003-03/msg00141.html (11,970 bytes)
8. Re: Gas No gas MIG (score: 1): Author: "Timothy F. Murphy" <timmurph@execpc.com>; Date: Tue, 11 Mar 2003 21:33:54 -0600; My partner and I recently purchased a Hobart MIG welder. We use 75% Argon and 25% CO2, which is the common gas for mild steel. The unit has 4 voltage settings and infinite wire feed up to about 150 i; /html/fot/2003-03/msg00161.html (9,408 bytes)
9. Re: Gas No gas MIG (score: 1): Author: WEmery7451@aol.com; Date: Wed, 12 Mar 2003 13:47:22 EST; Our boy bought a Mig Welder, after doing a sizable survey as to which make welder was the best. He ended up with a Hobart. What was left out of these discussions was whether these FOTer welders are 1; /html/fot/2003-03/msg00173.html (8,123 bytes)
10. RE: Gas No gas MIG (score: 1): Author: Bill Babcock <BillB@bnj.com>; Date: Wed, 12 Mar 2003 11:01:38 -0800; I have both a Lincoln MIG that I love and a Craftsman that I despise. I don't recall the model of the Lincoln, but it wasn't the bottom of the line and it wasn't inexpensive. the Lincoln is 220, and; /html/fot/2003-03/msg00174.html (9,179 bytes)
11. Re: Gas No gas MIG (score: 1): Author: "elliottd" <elliottd@look.ca>; Date: Wed, 12 Mar 2003 14:15:03 -0500; My SIP MIG welder uses Argon and CO2. It runs on 220 Volts, single phase. I had a lot of trouble with the feed. I'd be welding and the drive wheel that moves the wire forward would slip and the feed; /html/fot/2003-03/msg00179.html (10,452 bytes)
12. Re: Gas No gas MIG (score: 1): Author: Rikrock@aol.com; Date: Wed, 12 Mar 2003 16:54:47 EST; Greetings, I use a Miller 220 volt single phase MIG welder. Not a big one, I think max output is 185 amps. Works great. I think Miller owns Hobart, the similarity between some of their welders is har; /html/fot/2003-03/msg00180.html (8,690 bytes)
13. RE: Gas No gas MIG (score: 1): Author: Bill Babcock <BillB@bnj.com>; Date: Wed, 12 Mar 2003 13:54:27 -0800; I had min knurled, and it helped some, but the Lincoln is a lot more --Original Message-- From: elliottd To: Bill Babcock; WEmery7451@aol.com; timmurph@execpc.com; 19to1tr6@attbi.com Cc: fot@autox.te; /html/fot/2003-03/msg00181.html (10,689 bytes)
14. Re: Gas No gas MIG (score: 1): Author: "Timothy F. Murphy" <timmurph@execpc.com>; Date: Wed, 12 Mar 2003 19:55:53 -0600; Oops! Forgot to mention the input voltage. I was told before purchasing out welder to get the 220 Volt, single phase one, which I did. As I understand it, the duty cycle and capacity of the 110 Volt; /html/fot/2003-03/msg00188.html (8,543 bytes)
15. Re: Gas No gas MIG (score: 1): Author: Larry Young <cartravel@pobox.com>; Date: Wed, 12 Mar 2003 19:55:26 -0600; I bought a Miller 110v unit because I thought I'd be welding sheet metal. However, I find that I use it on a lot of heavy stuff too, e.g shortening Triumph upper A arms. I regret that I didn't bite t; /html/fot/2003-03/msg00189.html (8,657 bytes)
16. Re: Gas No gas MIG (score: 1): Author: "R. John Lye" <rjl@gt-classics.com>; Date: Wed, 12 Mar 2003 21:18:09 -0500; I'll second that - those helmets are wonderful! R. John Lye rjl6n@cstone.net; /html/fot/2003-03/msg00190.html (8,052 bytes)
17. Re: Gas No gas MIG (score: 1): Author: "Timothy F. Murphy" <timmurph@execpc.com>; Date: Wed, 12 Mar 2003 20:15:43 -0600; Yes, Miller and Hobart are made by the same company here in Wisconsin. The main difference (and almost the only difference) is that the Miller has a potentiometer for infinitely adjustable voltage an; /html/fot/2003-03/msg00194.html (9,074 bytes)
18. Re: Gas No gas MIG (score: 1): Author: "Keptin Komrade Dr. BobWrench III esq." <bownes@web9.com>; Date: Thu, 13 Mar 2003 09:55:12 -0500; I have one of the little, cheap Harbor Freight type 120V MIG welders and one of the HUGE Miller MIG 240 single phase welders. Like knives, each is different and has its place. The small one I can tos; /html/fot/2003-03/msg00199.html (9,599 bytes)
19. RE: Gas No gas MIG (score: 1): Author: "Russ Moore" <rem9@sunlink.net>; Date: Thu, 13 Mar 2003 11:53:36 -0500; I use a 220 volt single phase Lincoln SP-175 which does have gas. It also has stitch and spot modes and has been one of the most useful tools I have ever purchased. Parts (consumables) are inexpensiv; /html/fot/2003-03/msg00202.html (8,122 bytes)
20. Re: Gas No gas MIG (score: 1): Author: WEmery7451@aol.com; Date: Thu, 13 Mar 2003 13:08:26 EST; << The small one I can toss in the back of the car and haul across town to weld the stair rail at a friends house or keep in the trailer to put something together at the track. The above is the main; /html/fot/2003-03/msg00203.html (8,027 bytes)

Current List: 1 - 20
Page: [1] [2]