Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Heater\s+switch\s+and\s+fan\.\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Heater\s+switch\s+and\s+fan\.\s*$/: 7 ]

Total 7 documents matching your query.

1. Heater switch and fan. (score: 1): Author: James Schulte <schultejim@prodigy.net>; Date: Thu, 01 Nov 2001 19:05:27 -0800; Hi gang, I think I have a bad heater switch and a bad fan for the 70B. I'm using a test light to check this so stick with me. I get power from the double green wires on post 1 of the switch when I tu; /html/mgs/2001-11/msg00024.html (7,695 bytes)
2. Re: Heater switch and fan. (score: 1): Author: <paul.hunt1@virgin.net>; Date: Fri, 2 Nov 2001 18:57:38 -0000; Your diagnosis of the switch seems ok, but when you jumpered the switch did you still have good voltage on post 1? A high-resistance on the green could supply enough power to light your lamp but not; /html/mgs/2001-11/msg00040.html (8,568 bytes)
3. RE: Heater switch and fan. (score: 1): Author: Duinhoven_Hans@emc.com; Date: Mon, 5 Nov 2001 09:02:37 -0500; This switch is prone to not working when dirt has collected into it. Best is to open the switch carefully - remove the rocker. This can be done by prying a screwdriverblade on one of the sides. Caref; /html/mgs/2001-11/msg00082.html (8,293 bytes)
4. Re: Heater switch and fan. (score: 1): Author: James Schulte <schultejim@prodigy.net>; Date: Mon, 05 Nov 2001 17:23:33 -0800; Thanks for the reply. I was wondering if I could clean it. It seemed to work ok but no transfer of power was happening.. I'll let you know how I make out. Any suggestions on how and what to use to c; /html/mgs/2001-11/msg00104.html (8,833 bytes)
5. Re: Heater switch and fan. (score: 1): Author: James Schulte <schultejim@prodigy.net>; Date: Fri, 09 Nov 2001 09:03:18 -0800; I found a new switch in my box of goodies and it worked fine. I also cleaned the old switch inside and out with electrical spray cleaner and dabbed it with dielectric grease on all contact points (a; /html/mgs/2001-11/msg00235.html (9,122 bytes)
6. Re: Heater switch and fan. (score: 1): Author: Bob Howard <mgbob@juno.com>; Date: Fri, 9 Nov 2001 09:38:49 -0500; In the workshop manual is an exploded illustration of the fan. All you need to do, though, is to remove the fan from the heater box, separate the squirrel-cage blower from the shaft, then remove the; /html/mgs/2001-11/msg00237.html (8,561 bytes)
7. RE: Heater switch and fan. (score: 1): Author: Duinhoven_Hans@emc.com; Date: Mon, 12 Nov 2001 05:36:45 -0500; Yes it was me. First you should measure there is voltage inside the switch. As you now know how to open it, that's I think the easiest way. If not the feeding circuit is faulty - check the diagrams.; /html/mgs/2001-11/msg00282.html (10,161 bytes)

Current List: 1 - 7
Page: [1]