- 1. LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Tue, 04 Feb 2003 14:54:47 -0800
- Weelllll, ... I got a great deal on this LCB header from the MG Owner's club in England, it came with a nice exhaust sytem as well. Only one problem...the @#%* LCB header won't clear the steering sha
- /html/spridgets/2003-02/msg00092.html (8,351 bytes)
- 2. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Tue, 4 Feb 2003 17:14:55 -0600
- club seems /// unsubscribe/change address requests to majordomo@autox.team.net or try /// http://www.team.net/mailman/listinfo /// Archives at http://www.team.net/archive/spridgets
- /html/spridgets/2003-02/msg00095.html (9,054 bytes)
- 3. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Tue, 4 Feb 2003 19:13:42 -0500
- I installed a LCB on my car. It wouldn't clear the steering column either, but I was able to make it fit by: 1. Disconnecting the steering in the cockpit and the rack and pulling the whole thing aft
- /html/spridgets/2003-02/msg00102.html (10,199 bytes)
- 4. Fw: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Tue, 4 Feb 2003 19:46:06 -0500
- gee! i have a trailer and i forgot to remove the trailer...LOL! welds 2"-3" /// unsubscribe/change address requests to majordomo@autox.team.net or try /// http://www.team.net/mailman/listinfo /// Arc
- /html/spridgets/2003-02/msg00104.html (8,765 bytes)
- 5. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Tue, 4 Feb 2003 17:00:36 -0800 (PST)
- Depends - actually I just returned one to WC. I ordered a 2" (1 7/8id) LCB, per Bill and Will Perry's direction (www.rivergate5speed.com). WC sent a smaller one, different geometry from the Maniflow
- /html/spridgets/2003-02/msg00108.html (8,270 bytes)
- 6. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Tue, 4 Feb 2003 21:21:46 -0600
- /// unsubscribe/change address requests to majordomo@autox.team.net or try /// http://www.team.net/mailman/listinfo /// Archives at http://www.team.net/archive/spridgets
- /html/spridgets/2003-02/msg00111.html (8,722 bytes)
- 7. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Tue, 04 Feb 2003 19:32:27 -0800
- Wow, the LCB header from England is 1.5" OD but it is for a stock 1275 Which mine is. How big is the small one from Manifold? How much? thanks /// unsubscribe/change address requests to majordomo@aut
- /html/spridgets/2003-02/msg00112.html (9,079 bytes)
- 8. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Wed, 05 Feb 2003 08:59:37 -0800
- I saw a LCB header (Janspeed?) listed on Ebay several months ago that was described as RHD only!Someone had bought it from a UK vender & found it would not fit his LHD Spridget. Due to its design it
- /html/spridgets/2003-02/msg00128.html (9,648 bytes)
- 9. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Wed, 5 Feb 2003 21:07:33 -0000
- So you got a UK one designed for a car with a steering shaft on the How about this .. Fit the header to the engine upside-down... No, I am serious! I only mean temporarily as it would give you more r
- /html/spridgets/2003-02/msg00145.html (9,603 bytes)
- 10. Fw: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Wed, 5 Feb 2003 16:34:22 -0500
- ok i fudged the stupid trailer thing again! read below! chuck -- Original Message -- From "Charles Christ" <cfchrist at earthlink.net> To: "Guy Weller" <guy@weller-lakes.freeserve.co.uk>; <spridgets@
- /html/spridgets/2003-02/msg00148.html (8,878 bytes)
- 11. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Wed, 5 Feb 2003 22:05:18 -0000
- I guess you must be right. I had assumed from earlier posts that it was only a fraction of an inch mis-aligned. But then I have never even seen a LHD spridget so didn't realise the extent of the pro
- /html/spridgets/2003-02/msg00151.html (9,002 bytes)
- 12. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Wed, 5 Feb 2003 20:58:12 -0500
- cut and weld with tubing isa very frightening experience for most as it is a "do or die" job. getting the heat right and not having the tubing fall away at the last moment while trying to feed in the
- /html/spridgets/2003-02/msg00167.html (10,312 bytes)
- 13. Re: LCB header won't clear steering! (score: 1)
- Author: Unknown
- Date: Wed, 5 Feb 2003 19:55:56 -0800 (PST)
- 1.75 OD maybe? Too small for my application. 1.5 is smaller than I have on my 948 race engine. Call the Perry's at Rivergate. Maniflow is made in England, $169 for the WXL9. == "Know your stuff, be a
- /html/spridgets/2003-02/msg00173.html (8,234 bytes)
This search system is powered by
Namazu