- 1. PVC spacer plate (score: 1)
- Author: "Ken Ritacco" <ritacco0758@charter.net>
- Date: Mon, 19 Apr 2004 08:57:50 -0400
- Hello all this is my first post, I have a 1966 tiger Mk1A # B382001158. I'm running a F4B with a holley 1850 on a 5 bolt 289 hipo and would like to run a PCV system. I had installed a plastic 1/4 inc
- /html/tigers/2004-04/msg00117.html (7,526 bytes)
- 2. Re: PVC spacer plate (score: 1)
- Author: Steve Laifman <SLaifman@socal.rr.com>
- Date: Mon, 19 Apr 2004 10:56:12 -0700
- Both Seam (Moonstone) Ford and I have a lot of genuine Boss 302 1/4 inch spacer plates. They are well made, rare, and were purchased for the F4B use you envision. I am sure we can make a deal to sel
- /html/tigers/2004-04/msg00118.html (8,545 bytes)
- 3. Re: PVC spacer plate (score: 1)
- Author: Drmoonstone@aol.com
- Date: Mon, 19 Apr 2004 16:28:00 EDT
- The 302 spacer is of good quality and is made of a phenolic material. I have several new ones available, but doubt that they will work without hood modification. Moonstone
- /html/tigers/2004-04/msg00119.html (7,103 bytes)
- 4. Re: PVC spacer plate (score: 1)
- Author: "Ken Ritacco" <ritacco0758@charter.net>
- Date: Tue, 20 Apr 2004 18:59:49 -0400
- I am running the fiberglass LAT hood and did not have any clearance problems with the 1/4" spacer plate that was supplied buy Pony Carburetors, Inc.. I called Pony Carburetors , Inc today they said t
- /html/tigers/2004-04/msg00124.html (8,004 bytes)
- 5. Re: PVC spacer plate (score: 1)
- Author: "Ken Ritacco" <ritacco0758@charter.net>
- Date: Tue, 20 Apr 2004 19:11:14 -0400
- I spoke with Pony Carburetors, Inc today, they said they are selling Fomoco reproductions and have never had a problem, they are sending me another spacer plate free of charge. I am running a fibergl
- /html/tigers/2004-04/msg00126.html (9,956 bytes)
- 6. Re: PVC spacer plate (score: 1)
- Author: Steve Laifman <SLaifman@socal.rr.com>
- Date: Wed, 21 Apr 2004 12:09:32 -0700
- Thank you for dropping me a line concerning your successful use of a spacer plate on your LAT hood. Most of us have tried this approach and had considerable difficulties with various manufacturers o
- /html/tigers/2004-04/msg00128.html (8,975 bytes)
- 7. Re: PVC spacer plate (score: 1)
- Author: "Ken Ritacco" <ritacco0758@charter.net>
- Date: Wed, 21 Apr 2004 20:01:35 -0400
- I am running the F4B and I don't believe it was milled. The LAT hood is a reproduction. I did notice that I had two small rub marks on the underside of my Fiberglass hood as well as the outside corn
- /html/tigers/2004-04/msg00130.html (10,773 bytes)
- 8. Re: PVC spacer plate (score: 1)
- Author: Steve Laifman <SLaifman@socal.rr.com>
- Date: Wed, 21 Apr 2004 22:16:35 -0700
- Too close is too close. The REAL F4B LAT-1 did indeed have that front runner drilled and pipe thread tapped for a right angle hose fitting. That is the way is was done on the real think. The rear po
- /html/tigers/2004-04/msg00131.html (8,985 bytes)
- 9. Re: PVC spacer plate (score: 1)
- Author: "Ronak, TP (Timothy)" <Timothy.Ronak@AkzoNobel.com>
- Date: Thu, 22 Apr 2004 03:57:26 -0400
- Ken and listers, If you are shy some hood clearance you can gain about half an inch adopting the ram air base that I built for my car with the LAT glass hood and the RPM Performer Edelbrock manifold
- /html/tigers/2004-04/msg00132.html (8,609 bytes)
This search system is powered by
Namazu