Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*TR6\s+\-\s+Half\s+Shafts\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*TR6\s+\-\s+Half\s+Shafts\s*$/: 8 ]

Total 8 documents matching your query.

1. Re: TR6 - Half Shafts (score: 1): Author: Unknown; Date: Sun, 2 Jun 1996 17:41:23 -0400; supposed Those studs always pull out of the trailing arm. You have to helicoil the trailing armif the threads come out too (methinks it's 5/16-24) before reinstalling the studs. Clean them up real we; /html/triumphs/1996-06/msg00012.html (7,030 bytes)
2. Re: TR6 - Half Shafts (score: 1): Author: Unknown; Date: Sun, 16 Jun 1996 11:39:20 -0400; I whole heartedly agree. Dave TR6Massey@aol.com; /html/triumphs/1996-06/msg00436.html (6,394 bytes)
3. TR6 - Half Shafts (score: 1): Author: Unknown; Date: Tue, 28 May 1996 05:11:12 -0400; In Haynes and Bentley the same point is made about removing the rear axle shafts intact, that is, ensuring that the sliding shafts are not separated. Of course, this means that the stone guard for th; /html/triumphs/1996-05/msg00793.html (7,074 bytes)
4. Re: TR6 - Half Shafts (score: 1): Author: Unknown; Date: Wed, 29 May 1996 19:04:28 -0400; Fellow Motorheads, Indeed, why do both Haynes and Bentley have instructions to remove the half-shafts complete, after wiring them together? Granted, the wire will keep them from falling apart once ou; /html/triumphs/1996-05/msg00866.html (7,653 bytes)
5. Re: TR6 - Half Shafts (score: 1): Author: Unknown; Date: Thu, 30 May 1996 11:27:09 +0100; Ken: I was also very puzzled about the way the hub is held in place the first time I took it off. I am surprised that the hubs don't pull out of the trailing arms as the aluminium dissolves around th; /html/triumphs/1996-05/msg00889.html (7,493 bytes)
6. Re: TR6 - Half Shafts (score: 1): Author: Unknown; Date: Thu, 30 May 1996 13:55:44 -0400; Fellow Motorheads, Hope I didn't lead anyone astray regarding half-shaft removal, it seems that mine was made difficult by a replacement stone guard that's different from most--mine is made of heavy; /html/triumphs/1996-05/msg00892.html (7,246 bytes)
7. Re: TR6 - Half Shafts (score: 1): Author: Unknown; Date: Thu, 30 May 1996 13:06:22 -0700; The appropriate tool, a stud installer, is available from Sears and I'm sure Snap-On carries one. If you want, I can probably look up the Sears part number for you. A small pair of vise-grip pliers w; /html/triumphs/1996-05/msg00895.html (7,704 bytes)
8. Re[2]: TR6 - Half Shafts (score: 1): Author: Unknown; Date: Thu, 30 May 96 10:02:00 PST; =I did end up having a major adventure replacing the left rear outer u-joint =-- I was very near to giving up on removing one of the pairs bearing caps =from the yoke. It turned out that when I final; /html/triumphs/1996-05/msg00899.html (8,628 bytes)

Current List: 1 - 8
Page: [1]