Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Thermostat\s+housing\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Thermostat\s+housing\s*$/: 8 ]

Total 8 documents matching your query.

1. Thermostat housing (score: 1): Author: Theo Smit <TSmit@novatel.ca>; Date: Thu, 1 Oct 1998 10:09:46 -0600; So this morning the seeping thermostat housing started leaking rather more vigorously. The reason for the seep in the first place is that the DPO crossthreaded the cr*p out of the lower thermostat ho; /html/tigers/1998-10/msg00012.html (7,444 bytes)
2. Re: Thermostat housing (score: 1): Author: Craig Wright <craig@p-d-g.com>; Date: Thu, 01 Oct 1998 09:44:37 -0700; Hello Theo, If I were you, I'd try to install a Heli-coil in the bad bolt hole. You can buy a kit for different sizes at most large auto stores. The process is to drill the hole a littles larger and; /html/tigers/1998-10/msg00016.html (8,568 bytes)
3. Re: Thermostat housing (score: 1): Author: Bob Palmer <rpalmer@ames.ucsd.edu>; Date: Thu, 01 Oct 1998 11:24:06 -0700; can buy a kit for hole a littles larger. You then original, desired and hour. Craig, I assume that one-hour installation time doesn't include removing the radiator, which is necessary unless you happ; /html/tigers/1998-10/msg00019.html (7,811 bytes)
4. RE: Thermostat housing (score: 1): Author: Theo Smit <TSmit@novatel.ca>; Date: Thu, 1 Oct 1998 12:55:05 -0600; Bingo. Eyeball judgment says that the lower hole is also just obscured by the upper edge of the water pump, which means that has to come off also. If the thread that's in there is not too badly gored; /html/tigers/1998-10/msg00021.html (8,935 bytes)
5. Re: Thermostat housing (score: 1): Author: "Chris Richards" <richards@northcoast.com>; Date: Thu, 1 Oct 1998 12:05:38 -0400; hmmmm...cooling....hmmmm....short term solution....hmmmm Chris in Trinidad -- the the a tap so stress the can do Helicoil You about drill; /html/tigers/1998-10/msg00022.html (9,752 bytes)
6. Re: Thermostat housing (score: 1): Author: FRANK_BONIFAZI@HP-FtCollins-om4.om.hp.com; Date: Thu, 1 Oct 1998 14:01:37 -0600; I too have have used a Heli-Coil for this purpose. Actually a local shop put it in for me and its holding great. Don't forget to greese up the new bolts so you they don't break off like mine did whe; /html/tigers/1998-10/msg00026.html (9,190 bytes)
7. Re: Thermostat housing (score: 1): Author: Steve Laifman <laifman@flash.net>; Date: Thu, 01 Oct 1998 15:53:02 -0700; Well, Where do you suppose those bits of metal, generated from drilling and tapping, go? And is that where you want them? Bob, I have about three "right angle adapters". One a drill accessory, one an; /html/tigers/1998-10/msg00032.html (9,861 bytes)
8. RE: Thermostat housing (score: 1): Author: Theo Smit <TSmit@novatel.ca>; Date: Thu, 1 Oct 1998 17:09:52 -0600; It looked like a blind hole to me. In general, if you are concerned with metal chips falling into areas where you don't want them, then you can grease the tap (the drill bit, also, but you have to dr; /html/tigers/1998-10/msg00033.html (11,350 bytes)

Current List: 1 - 8
Page: [1]