Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Tile\s+Shop\s+Floors\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Tile\s+Shop\s+Floors\?\s*$/: 9 ]

Total 9 documents matching your query.

1. Re: Tile Shop Floors? (score: 1): Author: LBC286@aol.com; Date: Thu, 1 Jun 2000 08:47:07 EDT; << I have always disliked bare concrete, and even painted gray concrete floors. They look bad, don't reflect enough light (personal opinion), and are still a pain to clean up, and they stain, chip, p; /html/shop-talk/2000-06/msg00000.html (7,011 bytes)
2. Re: Tile Shop Floors? (score: 1): Author: "Kai M. Radicke" <kmr@pil.net>; Date: Thu, 1 Jun 2000 19:00:15 -0400; While it may be very appealing visually, I am concerned about it's practicality. Certainly it is NOT the type of surface which you would want to be carrying out any welding work near. Although, I bel; /html/shop-talk/2000-06/msg00004.html (7,651 bytes)
3. Re: Tile Shop Floors? (score: 1): Author: JGN <jgn@li.net>; Date: Fri, 2 Jun 2000 11:45:47 -0400 (EDT); 2x6 and 2x12. I 'store' it by placing it on the concrete floor in one or two garage bays. Cars are parked on top. The extra 1 1/2 to 3 inches (depending on how high it is stacked) makes it easier to; /html/shop-talk/2000-06/msg00008.html (8,628 bytes)
4. Re: Tile Shop Floors? (score: 1): Author: Douglas Shook <shook@usc.edu>; Date: Fri, 02 Jun 2000 09:31:47 -0700; I do think the "wooden garage floor violates building code" assertion probably is valid and probably does make logical sense. However, when I was young, I worked for GM in Flint, Michigan in the moto; /html/shop-talk/2000-06/msg00012.html (7,600 bytes)
5. Re: Tile Shop Floors? (score: 1): Author: JGN <jgn@li.net>; Date: Fri, 2 Jun 2000 17:00:09 -0400 (EDT); A lot of old plants were built this way. The IBM mainframe factory in NY still has 'em, too. Building codes were different back then and old installs are grandfathered in. A friend of mine runs an au; /html/shop-talk/2000-06/msg00021.html (8,655 bytes)
6. Tile Shop Floors? (score: 1): Author: "Kai M. Radicke" <kmr@pil.net>; Date: Mon, 29 May 2000 16:59:05 -0400; Has anyone done this? I have always disliked bare concrete, and even painted gray concrete floors. They look bad, don't reflect enough light (personal opinion), and are still a pain to clean up, and; /html/shop-talk/2000-05/msg00038.html (7,463 bytes)
7. Re: Tile Shop Floors? (score: 1): Author: Scott Hall <sch8489@garnet.acns.fsu.edu>; Date: Tue, 30 May 2000 01:14:54 -0400 (EDT); no, but I want to as well...just as soon as I get the stuff put away from the move... I dunno about actual ceramic tile... I originally wanted to go this route as well, but after looking a lot at hom; /html/shop-talk/2000-05/msg00039.html (9,350 bytes)
8. RE: Tile Shop Floors? (score: 1): Author: "Mitchell, Douglas (D.B.)" <dmitchel@ford.com>; Date: Tue, 30 May 2000 07:37:32 -0400; Kai, I have to agree with someone else about the ceramic tile. I don't know how well it will stand up to dropped tools or jack stands/floor jacks. The flooring you are thinking of with the aluminum s; /html/shop-talk/2000-05/msg00040.html (7,801 bytes)
9. Re: Tile Shop Floors? (score: 1): Author: "Donald H. Locker" <dhl@chelseamsl.com>; Date: Tue, 30 May 2000 15:54:20 -0400; I would think the in-floor heating would work quite well, even under vinyl tile. The heaters should not heat the floor to the point where the vinyl tile is stressed, or it would be hot enough for you; /html/shop-talk/2000-05/msg00041.html (8,769 bytes)

Current List: 1 - 9
Page: [1]