Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Welding\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Welding\s*$/: 14 ]

Total 14 documents matching your query.

1. Welding (score: 1): Author: "Stu Brennan" <stubrennan@mediaone.net>; Date: Fri, 15 Jun 2001 10:46:46 -0400; After taking well over an hour to fabricate and install a fix for my lawn mower last weekend, I realized that the repair would have taken about 5 minutes if I was set up for welding. Might prove hand; /html/tigers/2001-06/msg00067.html (7,809 bytes)
2. Re: Welding (score: 1): Author: Steve Laifman <SLaifman@SoCal.RR.com>; Date: Fri, 15 Jun 2001 09:46:23 -0700; There is a very good reason that MIG, TIG, or even CO2 inert gas welders are so popular. The inert gases prevent getting brittle crud in the weld, which significantly affects strength and appearance; /html/tigers/2001-06/msg00070.html (8,217 bytes)
3. Re: Welding (score: 1): Author: "Arden Bedell" <sixtysixtiger@hotmail.com>; Date: Fri, 15 Jun 2001 10:28:22 -0700; I agree with Steve: you'll be much happier with the results you get from a good MIG welder than you will from a stick welder, especially if you intend to use it weld thin sheet steel. I have a Linco; /html/tigers/2001-06/msg00072.html (10,274 bytes)
4. Re: Welding (score: 1): Author: "Arden Bedell" <sixtysixtiger@hotmail.com>; Date: Fri, 15 Jun 2001 11:19:14 -0700; Well...auto-stitching isn't quite the same thing. Auto-stitching just controls the on-off cycle of the welder as you move along your seam. So, basically you start at one end and move along at some (n; /html/tigers/2001-06/msg00073.html (9,963 bytes)
5. Re: Welding (score: 1): Author: "Arden Bedell" <sixtysixtiger@hotmail.com>; Date: Fri, 15 Jun 2001 11:24:26 -0700; --Arden pace alternating the tacks length is operation the Arden and usually; /html/tigers/2001-06/msg00074.html (10,983 bytes)
6. Re: Welding (score: 1): Author: SFordRB@aol.com; Date: Fri, 15 Jun 2001 16:52:54 EDT; I'm well aware of the method. As a retired Snap-On dealer (with no great affection for the company) the unit offered was intended to accomplish the same thing, less deformation and warping and less s; /html/tigers/2001-06/msg00075.html (7,590 bytes)
7. Welding (score: 1): Author: "Mike Sutter" <mjsutter@cts.com>; Date: Sun, 17 Jun 2001 00:10:43 -0700; I have a little 110 VAC wire feeder that I got from my wife for Christmas 5 years ago. Its a cheap little off-brand model that was sold by Harbor Freight for about $275.00. It is capable of both flu; /html/tigers/2001-06/msg00076.html (8,791 bytes)
8. Re: Welding (score: 1): Author: "Chris Hill" <Pirouette@uisreno.com>; Date: Fri, 15 Jun 2001 02:35:54 -0700; I think you both are saying about the same thing in result. But after taking on a real ruster (upside down, no rotisserie) with zero welding experience, I'd recommend what all the welding books say (; /html/tigers/2001-06/msg00078.html (7,916 bytes)
9. Welding (score: 1): Author: "Gary Strom" <gstrom@oldrepublic.com>; Date: Mon, 18 Jun 2001 12:42:56 -0500; Go with the little MIG welders. Do NOT go with an arc welder. The little 120 volt welders work great and are available from Northern Tool, Harbor Freight, your local "Farm and Fleet", or even Sam's,; /html/tigers/2001-06/msg00088.html (7,606 bytes)
10. Re: Welding (score: 1): Author: "Cullen Bennett" <r51465@email.sps.mot.com>; Date: Mon, 18 Jun 2001 12:09:52 -0700; Stu, You already have had a lot of very accurate and good info on the MIG wire feed welders. I now have a 220V Lincoln unit that works very nicely. Previously, I had a small 110V version (some off b; /html/tigers/2001-06/msg00089.html (8,724 bytes)
11. Welding (score: 1): Author: Stu Brennan <stubrennan@mediaone.net>; Date: Mon, 18 Jun 2001 20:22:35 -0400; Wow! Finally a topic on which the answers seems to converge! The consensus is that small MIG setup would probably do the job for me. Looking at a few of the "new" prices, I think I'll be looking in o; /html/tigers/2001-06/msg00090.html (7,536 bytes)
12. Re: Welding (score: 1): Author: SFordRB@aol.com; Date: Wed, 20 Jun 2001 15:23:41 EDT; Stu, check with Lincoln and Miller for factory refurbs/returns and demo units. In the past this was a great way to get a reduced price with good warranty. Haven't done this in five years so I don't k; /html/tigers/2001-06/msg00102.html (7,390 bytes)
13. Welding (score: 1): Author: "Brent Edinger" <banana111@msn.com>; Date: Thu, 21 Jun 2001 22:54:16 -0700; I have been using a MIG welder on my current Tiger restoration project. Does anyone have any tips on MIG welding upside down? I have trouble keeping the puddle on the material, it wants to drop off o; /html/tigers/2001-06/msg00105.html (7,381 bytes)
14. Re: Welding (score: 1): Author: "Chris Hill" <Pirouette@uisreno.com>; Date: Thu, 21 Jun 2001 00:27:07 -0700; I did alot of it ; sideways in awkward positions is fun too. The only thing I learned is that you can perfect the technique you mentioned by very strict attention to puddle color. When you key to a c; /html/tigers/2001-06/msg00107.html (7,995 bytes)

Current List: 1 - 14
Page: [1]