- 1. Wiper motor mounting grommets (score: 1)
- Author: "James Pickard" <geowiz.sgy@cox.net>
- Date: Fri, 13 Apr 2007 22:22:50 -0500
- OK folks, I need some help here. I've received a set of mounting grommets for the wiper motor for the bug-eye (Mo$$ part no. 280-755). Apparently, these fit in the three holes from the engine compart
- /html/spridgets/2007-04/msg00540.html (8,003 bytes)
- 2. Re: Wiper motor mounting grommets (score: 1)
- Author: Frank Clarici <spritenut@comcast.net>
- Date: Mon, 16 Apr 2007 12:24:19 -0400
- 1st mistake was getting them from them. But if you grease them up and get them started on one side then sort of pry them in with a screwdriver, they will fit. And just think in 30 days they will evap
- /html/spridgets/2007-04/msg00541.html (7,739 bytes)
- 3. Re: Wiper motor mounting grommets (score: 1)
- Author: derf <derf247@gmail.com>
- Date: Mon, 16 Apr 2007 10:25:52 -0600
- Cut em in half so you have one flat washer looking part and one that kinda looks like a "T" from the side. Insert the "T" part on top, use the flat part and a washer on the bottom. Or, you can try cu
- /html/spridgets/2007-04/msg00542.html (7,535 bytes)
- 4. Re: Wiper motor mounting grommets (score: 1)
- Author: "Mark" <mark@nashvilletn.org>
- Date: Mon, 16 Apr 2007 11:35:08 -0500
- I got one in with some silicone lube, I cut the others in half. When you buy rubber from Mo$$; if it is supposed to be soft it is hard and if it supposed to be hard it is soft. It will rot in about
- /html/spridgets/2007-04/msg00544.html (7,804 bytes)
- 5. Re: Wiper motor mounting grommets (score: 1)
- Author: "Michael Conn" <mconn2@bright.net>
- Date: Sun, 15 Apr 2007 22:20:45 -0400
- I've been in Ohio for the past 11 years since arriving from England. Michael
- /html/spridgets/2007-04/msg00545.html (7,349 bytes)
- 6. Re: Wiper motor mounting grommets (score: 1)
- Author: trevorwj@insightbb.com
- Date: Mon, 16 Apr 2007 12:33:02 -0400
- Someone else recently brought up this issue (Jack L?). I think he finally mad them fit using detergent and patience. Do NOT use petroleum products on rubber parts. It will shorten the life span. I us
- /html/spridgets/2007-04/msg00546.html (8,764 bytes)
- 7. Re: Wiper motor mounting grommets (score: 1)
- Author: "Michael Conn" <mconn2@bright.net>
- Date: Mon, 16 Apr 2007 09:02:19 -0400
- What's happened to the List? I keep getting messages of non-delivery. Michael
- /html/spridgets/2007-04/msg00547.html (7,333 bytes)
- 8. Re: Wiper motor mounting grommets (score: 1)
- Author: b-evans@earthlink.net
- Date: Mon, 16 Apr 2007 10:51:16 -0700
- The ones I brought back from AHSpares (http://www.ahspares.co.uk) worked just fine. And mine have not evaporated. Probably because Southern California is so pure and pollution-free* Buster *Now that
- /html/spridgets/2007-04/msg00556.html (7,699 bytes)
- 9. Re: Wiper motor mounting grommets (score: 1)
- Author: "Dan Gillitzer" <danginah@charter.net>
- Date: Mon, 16 Apr 2007 19:16:38 -0500
- I emailed Jim directly about this too. What I did on my Sprite is to put the grommets in boiling water, then take the container with the water and grommets out to the car. Pull one grommet out with a
- /html/spridgets/2007-04/msg00608.html (7,750 bytes)
- 10. Re: Wiper motor mounting grommets (score: 1)
- Author: "WJHS1960" <WJHS1960@comcast.net>
- Date: Mon, 16 Apr 2007 20:16:11 -0600
- <<What I did on my Sprite is to put the grommets in boiling water, then take the container with the water and grommets out to the car.>> WHY "work" so hard, guys?? Put one (or more if ya wanna) in yo
- /html/spridgets/2007-04/msg00614.html (7,526 bytes)
This search system is powered by
Namazu